The original Clack bypass valve for WS1 and WS1.25 systems The Clack Bypass Valve V3006 is an essential accessory for any professionally installed water softener or filter system. This sturdy assembly attaches directly to the inlet and outlet of your Clack WS1 or WS1.25 control valve. It allows you to disconnect the system from the water circuit in just two simple steps without having to interrupt the main water supply to the house. Security and control for homeowners The two red levers, which are easy to grip, allow you to switch easily between normal operation (‘Service’) and bypass (‘Bypass’). This proves extremely helpful for maintenance work such as refilling salt, changing resin or filter media, and disinfecting the system. If a fault or leak occurs in the system, you can isolate it immediately and still have water in your home. Complete set for flexible installation The set includes the one-piece bypass body made of high-strength, drinking water-approved Noryl and all necessary mounting materials. To ensure high compatibility with standard domestic installations, the commonly used 1 1/4-inch connection fittings (male thread) are typically included. The Clack system connection with union nuts and O-rings, which has proven to be reliable, enables quick, uncomplicated, and permanently tight installation on the control valve. Overview: Areas of application: Enables maintenance of the system during ongoing water operation In the event of malfunctions, the system can be quickly shut down and isolated Significantly facilitates the replacement of resin or filter media Standard equipment for professional and service-friendly installation Characteristics: Manufacturer: Clack Corporation Valve type: Bypass valve with two built-in shut-off valves Handling: Easy lever movement (90°) for “service” or “bypass” Material: High-strength, glass fiber-reinforced Noryl plastic Compatibility: Suitable for Clack WS1 and WS1.25

The CLACK bypass valve is generally used to isolate the filter or water softener from the mains pressure so that repairs or maintenance work can be carried out without interrupting the water supply to the household. The original Clack bypass valve for WS1.00 KTW systems The Clack Bypass Valve V3006-KTW is an essential accessory for any professionally installed water softener or filter system. This sturdy assembly attaches directly to the inlet and outlet of your Clack WS1.00 KTW control valve. It allows you to disconnect the system from the water circuit in just two simple steps without having to interrupt the main water supply to the house. Security and control for homeowners The two red levers, which are easy to grip, allow you to switch easily between normal operation (“Service”) and bypass (“Bypass”). This proves extremely helpful for maintenance work such as refilling salt, changing resin or filter media, and disinfecting the system. If a malfunction or leak occurs in the system, you can isolate it immediately and still have water in your home. Complete set for flexible installation The set includes the one-piece bypass body made of high-strength, drinking water-approved Noryl and all necessary mounting materials. To ensure high compatibility with standard domestic installations, the commonly used 1 1/4-inch connection fittings (male thread) are typically included. The Clack system connection with union nuts and O-rings, which has proven to be reliable, enables quick, uncomplicated, and permanently tight installation on the control valve. Product overview: Areas of application: Enables maintenance of the system during ongoing water operation In the event of malfunctions, the system can be quickly shut down and isolated Significantly facilitates the replacement of resin or filter media Standard equipment for professional and service-friendly installation Characteristics: Manufacturer: Clack Corporation Valve type: Bypass valve with two built-in shut-off valves Operation: Easy lever movement (90°) for “service” or “bypass” Compatibility: Suitable for Clack WS1.00 KTW

System separator with medium pressure zone Type BA – Series 580 Increase the integrity of your water supply with the Series 580 system separator – Type BA Protect your drinking water system effectively with the groundbreaking Series 580 backflow preventer. This sophisticated device is specifically designed to prevent backflow in water supply systems by creating a secure separation between clean drinking water and potentially contaminated water. Advanced materials and construction The 580 series is made of brass, which is not only durable and offers excellent corrosion resistance, but is also resistant to dezincification. Elements constructed with screw connections can be installed both horizontally and vertically. This ensures maximum application flexibility. Certifications that build trust This backflow preventer is certified according to EN 12729 and EN 1717 and has been approved by the DVGW, qualifying it for use in critical water supply systems. The recognised certificates prove that the 580 series meets all necessary safety standards and is a reliable solution for protecting drinking water. Areas of application and adaptability The 580 series is perfect for a variety of applications, from private to commercial to industrial installations. Its suitability for different installation orientations makes it the preferred choice for a wide range of requirements and spatial conditions. Easy maintenance and sustainable performance Thanks to its design, maintenance of this system separator is particularly easy for the user. Quick access to internal components reduces maintenance times and ensures consistently high performance and operational reliability. Choose the 580 series Use the advanced technology of the 580 series to ensure a safe and reliable water supply. Thanks to its excellent backflow protection, the quality of the water and the service life of your system can be improved. Investing in the 580 series offers you a robust, reliable and maintenance-friendly solution that meets your requirements for a safe water supply. Product description Type BA 580 series backflow preventers with a medium pressure zone have been specially developed for the safe separation of drinking water networks from non-drinking water sources. The screw-fixed connections on these devices allow for flexible installation in both horizontal and vertical orientations. Brass housing without dezincification, AG connections with union nut and dirt filter at the inlet, suitable for horizontal or vertical installation, EN 12729 certified, incl. maintenance booklet, PN 10, max. operating temperature 65 °C Technical details Temperature range: 0–65 °C Nominal pressure (PN): PN 10 Material: Dezincification-resistant brass DR Certifications: EN 12729, EN 1717 and DVGW Possible areas of application The 580 series backflow preventers are ideal for installations where reliable separation of drinking and non-drinking water is crucial. They are suitable for use in private households, commercial buildings and industrial facilities where they meet water quality and safety requirements. These backflow preventers are made of dezincification-resistant brass, which gives them long-term reliability and corrosion resistance and makes them particularly durable. Their DVGW certification proves that they meet the highest standards in terms of safety and performance. Use of water softening systems only in conjunction with a system separator In a water softening system, a system separator serves to protect the drinking water network from backflow of softened water or other substances from the system and to ensure the quality of the drinking water. The backflow preventer closes automatically when the pressure in the system changes. This prevents contaminated or altered water from entering the public drinking water network. Legal information The water softener is installed either centrally after the municipal water meter and the fine filter, or directly before the consumer or hot water supply in the hard water pipe. During installation, DIN EN 806, DIN EN 1717 and DIN 1988 as well as locally applicable regulations must be observed. A system separator must be installed before the water softening system in particular!

The professional maintenance key for your Clack valves (WS1.00-WS1.50) The Clack maintenance key V3193-02 is an indispensable special tool for every system owner, installer and service technician. This durable tool made of high-strength plastic is precisely tailored to the dimensions of the large screw connections on Clack control valves. Its main function is to enable the plastic components to be tightened and loosened professionally and, above all, without damage. EASY TO USE: The spanner has been designed to enable quick and easy replacement of the filter cartridges. VERSATILE TOOL: The maintenance key (V3193-02) is used in water softeners and filter systems. This key can be used to remove and tighten pistons and to mount and dismantle nuts and fittings on valves. LONG-LASTING AND RELIABLE: The spanner is made from premium materials, is robust and can withstand the demands of regular use without any problems. EFFICIENT MAINTENANCE: Using the right spanner ensures that maintenance is carried out properly and your water softener is not damaged. This saves you time and money on repairs. Avoiding costly damage caused by unsuitable tools The most common cause of damage to the plastic parts of a control valve is the use of unsuitable tools such as pipe wrenches. This often results in scratched surfaces, deformed corners or even hairline cracks in the union nuts and covers, which can lead to leaks and costly repairs. With its precisely fitting shape, this spanner grips the designated ribs across their entire surface and transfers the force optimally without damaging the components. A tool for various activities This multifunctional key was developed for the most common service tasks on the WS1.00, WS1.25 and WS1.50 valve series. The large side of the wrench fits exactly onto the large union nut that secures the valve to the pressure tank. The smaller side is used to tighten and loosen the injector cover. This tool enables you to carry out essential maintenance work on your system professionally and safely. Overview: Areas of application Tightening and loosening the main union nut on the pressure tank in accordance with technical specifications Securely mounting and removing the injector cover Prevents damage to plastic screw connections Standard tool for plant owners, fitters and service technicians Features Manufacturer: Clack Corporation Variant: Multifunctional maintenance key/assembly tool Function: Working on valve screw connections without causing damage Material: High-strength, glass fibre reinforced plastic Compatibility: For Clack WS1.00, WS1.25 and WS1.50 control valves

The standard connection set is the right choice for standard domestic use. If your water softener is being installed in a detached house and the water is not affected by additives, this option offers a reliable and economical solution. The integrated backflow preventer in the Neomeris water softener ensures that water flows in one direction only and protects the domestic plumbing system from backflow. For standard applications without any particular hygiene risks, this protection is entirely sufficient. The appropriate connection kit consists of: Double nipple (Item No.: 882103) Connection fitting (Item No.: 882068) 2 x 100 cm flexible hose, 1”, female thread on both ends for water softener inlet (Item No.: 882069) Waste water hose (Item No.: 882070) Hose clamp (Item No.: 882071) ITP Multitri = free outlet (Item No.: 882072) Duroval A (Item No.: 400010)

Clack seal and spacer set for WS 1.00 KTW, WS 1.25 KTW, and WS 1.50 KTW The seal kit for your Clack WS 1.00 KTW, WS 1.25 KTW, and WS 1.50 KTW valves The Clack Seal and Spacer Kit V3005-02-KTW is the second essential wear parts kit required for a complete and sustainable overhaul of your control valve. The control piston is the moving part, while this kit forms the stationary “cylinder liner” in the valve housing. These seals are crucial for the precise separation of the different water paths during regeneration. The perfect complement to piston replacement The seals used in the valve housing can harden, wear out, or become damaged by dirt particles after prolonged use. This causes internal leaks, which produce the same symptoms as a worn piston: constant water flow to the waste water, reduced performance, or salty soft water. When replacing the control piston, it is strongly recommended that you also replace the V3005-02-KTW seal kit to ensure a professional and permanent repair. Complete set for easy installation The seal kit is supplied as a pre-assembled unit in which all sealing rings and spacers are already correctly arranged. This allows for easy and error-free “push-in” installation in the cylinder valve housing. This set is an indispensable standard replacement part for households with a water softener system with a Clack valve, as it is highly compatible with the WS 1.00 KTW, WS 1.25 KTW, and WS 1.50 KTW valve series. Areas of application Complete overhaul of Clack WS 1.00 KTW, WS 1.25 KTW, and WS 1.50 KTW valves Elimination of internal leaks and continuous discharge into wastewater When replacing the control piston, this component is normally also replaced Valve regains precise hydraulic control Characteristics Manufacturer: Clack Corporation Variant: Complete, stationary seal and spacer kit Function: Seals the chambers in the main valve cylinder Material: High-quality EPDM seals and low-wear plastic spacers Compatibility: Universally compatible with Clack WS 1.00, WS 1.25, and WS 1.50 control valves Manufacturer's product number: V3005-02-KTW