Tip
0-130 °C - S8 screw head pH electrode without temperature probe - combination electrode JUMO tecLine HD (201021/10-12-04-82-120/000)
Product number:
800072
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Measuring resistor (temperature sensor):
without
The JUMO "Heavy Duty" pH electrode records the pH value of water and aqueous media. The rugged industrial electrode is designed for the most demanding applications with increased dirt and toxic loads as well as oily media.Advantages:stable and reliable measured values
low maintenance and robustextended service lifeSelected version:without temperature sensorS8 N-srew head Pg13,5, PPS
materialPTFE ring diaphragmInsertion length 120mm (standard)Type code (can also be found on your electrode): 201021/10-12-04-18-120/841Features: for industrial applications; also in heavy-duty and hygienic version for demanding processes; integrated temperature sensorApplication range: process measurement; high temperature applications; suspensions; electroplating; lacquers; waste water; ultrapure water; water; always contaminated media; hygienic and sterile applications; boiler feed water If you require other versions of this electrode, please use our configurator and configure the suitable electrode for you. You can download the JUMO data sheet just below our text. You will find our configurator on page 6 of the data sheet. Please note that the delivery time for freely configured electrodes is 5 to 6 weeks.
From
€227.92*
Tip
0-130 °C, hole diaphragm, PT1000 - Variopin pH electrode - combination electrode JUMO tecLine HD (201021/10-12-11-18-120/841)
Product number:
800074
Diaphragm:
Hole diaphragm
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Measuring resistor (temperature sensor):
PT1000
The JUMO "Heavy Duty" pH electrode records the pH value of water and aqueous media. The rugged industrial electrode is designed for the most demanding applications with increased dirt and toxic loads as well as oily media.Advantages:stable and reliable measured values
low maintenance and robustextended service lifeSelected version:PT1000 temperature sensorVarioPin electrode head (always required for versions with temperature sensor)Hole diaphragmInsertion length 120mm (standard)Type code (can also be found on your electrode): 201021/10-12-11-18-120/841Features: for industrial applications; also in heavy-duty and hygienic version for demanding processes; integrated temperature sensorApplication range: process measurement; high temperature applications; suspensions; electroplating; lacquers; waste water; ultrapure water; water; always contaminated media; hygienic and sterile applications; boiler feed water If you require other versions of this electrode, please use our configurator and configure the suitable electrode for you. You can download the JUMO data sheet just below our text. You will find our configurator on page 6 of the data sheet. Please note that the delivery time for freely configured electrodes is 5 to 6 weeks.
From
€321.29*
Tip
0-130 °C, PT100 - Variopin pH electrode - combination electrode JUMO tecLine HD (201021/10-12-04-18-120/840)
Product number:
800088
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Measuring resistor (temperature sensor):
PT100
The JUMO "Heavy Duty" pH electrode records the pH value of water and aqueous media. The rugged industrial electrode is designed for the most demanding applications with increased dirt and toxic loads as well as oily media.Advantages:stable and reliable measured values
low maintenance and robustextended service lifeSelected version:PT100 temperature sensorVarioPin electrode head (always required for versions with temperature sensor)PTFE ring diaphragmInsertion length 120mm (standard)Type code (can also be found on your electrode): 201021/10-12-04-18-120/840Features: for industrial applications; also in heavy-duty and hygienic version for demanding processes; integrated temperature sensorApplication range: process measurement; high temperature applications; suspensions; electroplating; lacquers; waste water; ultrapure water; water; always contaminated media; hygienic and sterile applications; boiler feed water If you require other versions of this electrode, please use our configurator and configure the suitable electrode for you. You can download the JUMO data sheet just below our text. You will find our configurator on page 6 of the data sheet. Please note that the delivery time for freely configured electrodes is 5 to 6 weeks.
From
€290.09*
Tip
0-130 °C, PT1000 - Variopin pH electrode - combination electrode JUMO tecLine HD (201021/10-12-04-18-120/841)
Product number:
800073
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Measuring resistor (temperature sensor):
PT1000
The JUMO "Heavy Duty" pH electrode records the pH value of water and aqueous media. The rugged industrial electrode is designed for the most demanding applications with increased dirt and toxic loads as well as oily media.Advantages:stable and reliable measured values
low maintenance and robustextended service lifeSelected version:PT1000 temperature sensorVarioPin electrode head (always required for versions with temperature sensor)PTFE ring diaphragmInsertion length 120mm (standard)Type code (can also be found on your electrode): 201021/10-12-04-18-120/841Features: for industrial applications; also in heavy-duty and hygienic version for demanding processes; integrated temperature sensorApplication range: process measurement; high temperature applications; suspensions; electroplating; lacquers; waste water; ultrapure water; water; always contaminated media; hygienic and sterile applications; boiler feed water If you require other versions of this electrode, please use our configurator and configure the suitable electrode for you. You can download the JUMO data sheet just below our text. You will find our configurator on page 6 of the data sheet. Please note that the delivery time for freely configured electrodes is 5 to 6 weeks.
From
€290.83*
JUMO tecLine - pH glass shaft electrode with salt reserve, 120mm insertion length, PTFE ring and HA glass (for high alkali applications)
Product number:
800196
Active part:
HA glass: pH 0 ... 14; -5 ... +80°C (high alkali use)
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€183.02*
JUMO tecLine - pH glass shaft electrode with salt reserve, 120mm installation length, annular gap diaphragm and UW glass
Product number:
800199
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
Ring-gap diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€252.15*
JUMO tecLine - pH glass shaft electrode without extra code, 120mm insertion length, PTFE ring and UW glass
Product number:
800197
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
without (000)
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€173.39*
JUMO tecLine pH electrode (glass shaft + high-temperature gel, 1x zirconium dioxide, screw head Pg13.5, 120mm, without extra code)
Product number:
800224
Active part:
HT-Glas: pH 0 ... 14; -5 ... +135°C
|
Basic type supplement:
Glass shaft, high-temperature gel, sealed, cartridge discharge system
|
Diaphragm:
1x zirconium dioxide
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
without (000)
|
Insertion length:
120mm
Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV
From
€173.39*
JUMO tecLine pH electrode (glass shaft + high-temperature gel, perforated diaphragm, screw head Pg13.5, 120mm, salt reserve)
Product number:
800249
Active part:
HT-Glas: pH 0 ... 14; -5 ... +135°C
|
Basic type supplement:
Glass shaft, high-temperature gel, sealed, cartridge discharge system
|
Diaphragm:
Hole diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
120mm
Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV
From
€213.81*
JUMO tecLine pH electrode (glass shaft + high-temperature gel, perforated diaphragm, VP plug-in head Pg13.5, 120mm, salt reserve, PT100)
Product number:
800339
Active part:
HT-Glas: pH 0 ... 14; -5 ... +135°C
|
Basic type supplement:
Glass shaft, high-temperature gel, sealed, cartridge discharge system
|
Diaphragm:
Hole diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Salt reserve + with integrated Pt100
|
Insertion length:
120mm
Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV
From
€277.30*
JUMO tecLine pH electrode (glass shaft, hole diaphragm, VP plug-in head, 120mm, salt reserve, Pt100)
Product number:
800338
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
Hole diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Salt reserve + with integrated Pt100
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€277.30*
JUMO tecLine pH electrode (glass shaft, perforated diaphragm, screw head Pg13.5, 120mm, salt reserve)
Product number:
800222
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
Hole diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€213.81*
JUMO tecLine pH electrode (glass shaft, PTFE ring, screw head Pg13.5, 225mm, salt reserve)
Product number:
800223
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
225mm
High-quality industrial electrodesprocess/industrial applicationsadditional integrable temperature probedifferent installation lengthsspecial types on request
From
€204.93*
JUMO tecLine pH electrode (glass shaft, PTFE ring, screw head Pg13.5, 225mm)
Product number:
800337
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
without (000)
|
Insertion length:
225mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€195.30*
JUMO tecLine pH electrode (glass shaft, PTFE ring, VP plug-in head, 120mm, PT100)
Product number:
800336
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Temperature sensor Pt100
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€236.88*
JUMO tecLine pH electrode (glass shaft, PTFE ring, VP plug-in head, 120mm)
Product number:
800198
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Salt reserve + with integrated Pt100
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity
From
€246.51*
JUMO tecLine PRO pH electrode (process electrode, HT glass, annular gap diaphragm, screw head Pg13.5, salt reserve)
Product number:
800341
Active part:
HT-Glas: pH 0 ... 14; 0 ... +110°C
|
Diaphragm:
Ring-gap diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
General descriptionThe electrodes are characterised by high mechanical and chemical resistance. Due to the stable PVDF body, there is practically no risk of the sensor breaking. The electrolyte of these combination electrodes guarantees a stable measured value, even in critical media containing sulphite.A Pt1000 temperature sensor is integrated. Depending on the application, the electrodes can be manufactured as pH or redox electrodes. An open annular gap diaphragm is used as the diaphragm.Areas of applicationChemical industryWaste water treatmentSewage treatmentPaper industrySelected version:Basic type: JUMO tecLine PRO pH combination electrodeBasic type extension: Process electrodeActive part: HT glassDiaphragm: annular gap diaphragmElectrical connection to electrode: Screw head Pg13.5Extra codes: Salt reserveOrder code: 201020/79-12-10-22/837
From
€327.52*
JUMO tecLine PRO pH electrode (process electrode, HT glass, annular gap diaphragm, VP plug-in head, salt reserve, integrated Pt1000)
Product number:
800343
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Diaphragm:
Ring-gap diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Salzreserve + mit integriertem Pt1000
General descriptionThe electrodes are characterised by high mechanical and chemical resistance. Due to the stable PVDF body, there is practically no risk of the sensor breaking. The electrolyte of these combination electrodes guarantees a stable measured value, even in critical media containing sulphite.A Pt1000 temperature sensor is integrated. Depending on the application, the electrodes can be manufactured as pH or redox electrodes. An open annular gap diaphragm is used as the diaphragm.Areas of applicationChemical industryWaste water treatmentSewage treatmentPaper industrySelected version:Basic type: JUMO tecLine PRO pH combination electrodeBasic type extension: Process electrodeActive part: HT glassDiaphragm: annular gap diaphragmElectrical connection to electrode: VP plug-in head Pg13.5Extra codes: Salt reserve, with integrated Pt1000Order code: 201020/79-12-10-18/837, 841
From
€390.93*
JUMO tecLine PRO pH electrode (process electrode, UW glass, annular gap diaphragm, screw head Pg13.5, salt reserve)
Product number:
800340
Active part:
UW glass: pH 0 ... 12 (14 for short periods); -5 ... +80°C
|
Diaphragm:
Ring-gap diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
General descriptionThe electrodes are characterised by high mechanical and chemical resistance. Due to the stable PVDF body, there is practically no risk of the sensor breaking. The electrolyte of these combination electrodes guarantees a stable measured value, even in critical media containing sulphite.A Pt1000 temperature sensor is integrated. Depending on the application, the electrodes can be manufactured as pH or redox electrodes. An open annular gap diaphragm is used as the diaphragm.Areas of applicationChemical industryWaste water treatmentSewage treatmentPaper industrySelected version:Basic type: JUMO tecLine PRO pH combination electrodeBasic type extension: Process electrodeActive part: UW glassDiaphragm: annular gap diaphragmElectrical connection to electrode: screw head Pg13.5Extra codes: Salt reserveOrder code: 201020/79-18-10-22/837
From
€327.52*
JUMO tecLine PRO pH electrode (process electrode, UW glass, annular gap diaphragm, VP plug-in head, salt reserve, integrated Pt1000)
Product number:
800342
Active part:
HT-Glas: pH 0 ... 14; 0 ... +110°C
|
Diaphragm:
Ring-gap diaphragm, gel of polymerised solid electrolyte ("diaphragmless")
|
Electrical connection of the electrode (onto which the cable is plugged):
VarioPin (VP) plug-in head Pg13.5
|
Extra code:
Salzreserve + mit integriertem Pt1000
General descriptionThe electrodes are characterised by high mechanical and chemical resistance. Due to the stable PVDF body, there is practically no risk of the sensor breaking. The electrolyte of these combination electrodes guarantees a stable measured value, even in critical media containing sulphite.A Pt1000 temperature sensor is integrated. Depending on the application, the electrodes can be manufactured as pH or redox electrodes. An open annular gap diaphragm is used as the diaphragm.Areas of applicationChemical industryWaste water treatmentSewage treatmentPaper industrySelected version:Basic type: JUMO tecLine PRO pH combination electrodeBasic type extension: Process electrodeActive part: UW glassDiaphragm: annular gap diaphragmElectrical connection to electrode: VP plug-in head Pg13.5Type supplements: Salt reserve, with integrated Pt1000Order code: 201020/79-18-10/837, 841
From
€390.93*
JUMO tecLine redox electrode (glass shaft, platinum tip, PTFE ring, screw head Pg13.5, 120mm, salt reserve)
Product number:
800331
Active part:
Platinum tip, redox measuring range ±2000 mV, -5 ... +90°C
|
Basic type supplement:
Glass shaft, cartridge deflection system
|
Diaphragm:
PTFE - ring
|
Electrical connection of the electrode (onto which the cable is plugged):
Screw head Pg13.5 (S8)
|
Extra code:
Salt reservoir (837)
|
Insertion length:
120mm
Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivitySelected version:Basic type: Glass shaftActive part: Platinum capDiaphragm: PTFE ringElectrical connection to electrode: screw head Pg13.5 (S8)Insertion length: 120mm (standard)Extra codes: Salt reserveOrder code: 201025/51-22-04-22-120/837
From
€247.01*
NeoTec Select Sensor Conductivity modular measuring package with 4-20mA head transmitter
Product number:
891015
Head transmitter:
4-20 mA
|
Tee:
1" flow cell with 3/4" inner thread NPT
|
measuring range:
1-10.000 μS/cm
The conductivity measuring package consists of a 3 meter connection cable, a 4-20mA head transmitter, and the conductivity sensor. Due to the design of the sensor assembly, only the sensor needs to be replaced, when it should be worn out . All other components of this system can be used continuously. For an optimal process integration the NeoTec sensor is delivered with a fitting T-piece.
Advantages:
preconfigured for NeoTecMaster®
modular design
industry standard
resource friendly
€743.25*
NeoTec Select Sensor Conductivity modular measuring package with 4-20mA head transmitter for low measuring range
Product number:
891016
Head transmitter:
4-20 mA
|
Tee:
1.5" flow cell with 1" inner thread NPT
|
measuring range:
0.1-1.000 μS/cm
The conductivity measuring package consists of a 3 meter connection cable, a 4-20mA head transmitter, and the conductivity sensor. Due to the design of the sensor assembly, only the sensor needs to be replaced, when it should be worn out . All other components of this system can be used continuously. For an optimal process integration the NeoTec sensor is delivered with a fitting T-piece.
Advantages:
preconfigured for NeoTecMaster®
modular design
industry standard
resource friendly
€780.50*
NeoTec Select Sensor Conductivity modular measuring package with Modbus signal output
Product number:
891012
Head transmitter:
Modbus 12-24 VDC
|
Tee:
1" flow cell with 3/4" inner thread NPT
|
measuring range:
1-10.000 μS/cm
The conductivity measuring package consists of a 3 meter connection cable, a Modbus head transmitter, and the conductivity sensor. Due to the design of the sensor assembly, only the sensor needs to be replaced, when it should be worn out . All other components of this system can be used continuously. For an optimal process integration the NeoTec sensor is delivered with a fitting T-piece.
Advantages:
preconfigured for NeoTecMaster®
modular design
industry standard
resource friendly
€743.25*