emec K-Plus dosing pump

Suction lance for extracting a medium directly from a supply container (canister/IBC/CNT tank/barrel)Foot valve with pre-filter and non-return valve. The level switch generates a digital empty signal. Venting nipple 4mm for return of venting hose from dosing pump or overpressure/multifunction valve.Our suction lances can be adjusted in height, this means that, for example, instead of pumping from a 50 litre container, you can also pump from a 10, 20 or 30 litre container with the 40cm suction lance.Series: LASP4Material O-ring: EPDM (neutral) or FP (Viton)Immersion length: 40cm, 75cm or 122cmConnection on the unit side: M12 or BNCThread/hose connection (mm): 1/2 4x6 (suction capacity max 10l/h)Number of suction connections: 1-suction connectionMounting connection: C61 canister connection (for 40cm suction lance) or mounting connection 1 1/2" CNT/IBC (for 122cm suction lance)Number of floats/switching direction/electrical connection: 1st level/N.O/M12(PRIUS/PRISMA)Length of connection cable: 3.5mIntake filter: LASP4Special feature: Valve ball ceramic frequently asked questions What can I use the emec LASP4 suction lance for? It is suitable for the clean extraction of liquids from tanks or canisters. Is the suction lance compatible with my pump? Yes, it is compatible with standard emec pump models. How long is the suction lance? The LASP4 has a practical length of 4 metres for deeper containers. What material is the suction lance made of? Robust metal and high-quality plastics ensure durability and stability. Is the suction lance easy to clean? Yes, it can be quickly dismantled and thoroughly rinsed. Can I also use it for liquids containing oil? Yes, it is suitable for water, oil and other low-viscosity substances. Do I need tools for assembly? No, the suction lance is supplied ready-assembled and is immediately ready for use.

Suction lance for extracting a medium directly from a supply container (canister/IBC/CNT tank/barrel)Foot valve with pre-filter and non-return valve. The level switch generates a digital empty signal. Venting nipple 4mm for return of venting hose from dosing pump or overpressure/multifunction valve.Our suction lances can be adjusted in height, this means that, for example, instead of pumping from a 50 litre container, you can also pump from a 10, 20 or 30 litre container with the 40cm suction lance.Series: LASP4Material O-ring: EPDM (neutral) or FP (Viton)Immersion length: 40cm, 75cm or 122cmConnection on the unit side: M12 or BNCThread/hose connection (mm): 1/2 4x6 (suction capacity max 10l/h)Number of suction connections: 1-suction connectionMounting connection: C61 canister connection (for 40cm suction lance) or mounting connection 1 1/2" CNT/IBC (for 122cm suction lance)Number of floats/switching direction/electrical connection: 1st level/N.O/M12(PRIUS/PRISMA)Length of connection cable: 3.5mIntake filter: LASP4Special feature: Valve ball ceramic frequently asked questions What can I use the emec LASP4 suction lance for? It is suitable for the clean extraction of liquids from tanks or canisters. Is the suction lance compatible with my pump? Yes, it is compatible with standard emec pump models. How long is the suction lance? The LASP4 has a practical length of 4 metres for deeper containers. What material is the suction lance made of? Robust metal and high-quality plastics ensure durability and stability. Is the suction lance easy to clean? Yes, it can be quickly dismantled and thoroughly rinsed. Can I also use it for liquids containing oil? Yes, it is suitable for water, oil and other low-viscosity substances. Do I need tools for assembly? No, the suction lance is supplied ready-assembled and is immediately ready for use.

The emec service set for the K-Plus pump consists of the pump head, including sealing ring and a diaphragm, which is the same for all versions of the pump and is made of PTFE. Our service sets are available in the versions I, L and M. The only difference is the size of the pump head, which varies according to pressure and flow rate. The second choice on your part determines the material of the pump head and the material of the sealing ring. The correct selection of the service set, i.e. the correct choice of pump head size and pump head and seal material, can easily be made via your K-series pump type plate as follows. 1. On the type plate of your K-PLUS pump you will find the pressure "bar xxx - PSI xxx" above the serial number and then the pump capacity "l/h xxx - gph xxx". With these two items of information, you can easily determine the correct pump head size (I, L, M). (see example picture of type plate in the article) Version I 1 bar / 3 litres per hour 1 bar / 5 litres per hour 1 bar / 20 litres per hour Version L 5 bar / 10 litres per hour 8 bar / 8 litres per hour 10 bar / 5 litres per hour 15 bar / 4 litres per hour 18 bar / 2 litres per hour Version M 2 bar / 18 litres per hour 2. hidden in the "code" on the type plate you will find the reference to the pump head mounted at delivery and its sealing material. The ninth character indicates the sealing material. (see example picture of the type plate in the article) The most common types are listed below and these are shown via our selection matrix: K = PVDF pump head with Viton seal D = PP pump head with EPDM seal A = PMMA pumphead with Viton seal R = PMMA pumphead with EPDM seal Z = Stainless steel with Viton seal £ = Stainless steel pump head with EPDM gasket  (other types are available on request) Service set contents: PVDF pump head with Viton seal:1x pump head (dosing head) incl. seal 1x PTFE diaphragm- Stainless steel screws and caps (only for L and M service set) PP pump head with EPDM seal:1x pump head (dosing head) incl. seal  1x PTFE diaphragm - Stainless steel screws and caps (only for L and M service set)PMMA pump head with Viton or EPDM seal:1x pump head (dosing head) incl. seal 1x PTFE diaphragm - Stainless steel screws and caps (only for L and M service set) *Stainless steel pump head with Viton or EPDM seal:1x seal without pump head (no change required as stainless steel) 1x PTFE diaphragm frequently asked questions Is this service kit compatible with my emec K-Plus pump? Yes, if your pump is size ‘I’. You can check this on the pump’s type plate. What does the service kit contain? You will receive a new pump head with a seal, as well as a suitable diaphragm for replacement. When should I replace the service kit? If the pump’s performance has deteriorated, it’s leaking, or it hasn’t been serviced for a long time. Can I carry out the replacement myself? Many customers replace the pump head and diaphragm themselves. With a bit of DIY skill, it’s usually a quick job. How can I tell if my diaphragm or seal is worn out? Typical signs include dripping from the pump head, uneven flow or a loss of pressure. Why is it worth replacing the parts rather than buying a new pump? With the service kit, you can quickly restore your pump to a reliable working condition.

The emec service set for the K-Plus pump consists of the pump head, including sealing ring and a diaphragm, which is the same for all versions of the pump and is made of PTFE. Our service sets are available in the versions I, L and M. The only difference is the size of the pump head, which varies according to pressure and flow rate. The second choice on your part determines the material of the pump head and the material of the sealing ring. The correct selection of the service set, i.e. the correct choice of pump head size and pump head and seal material, can easily be made via your K-series pump type plate as follows. 1. On the type plate of your K-PLUS pump you will find the pressure "bar xxx - PSI xxx" above the serial number and then the pump capacity "l/h xxx - gph xxx". With these two items of information, you can easily determine the correct pump head size (I, L, M). (see example picture of type plate in the article) Version I 1 bar / 3 litres per hour 1 bar / 5 litres per hour 1 bar / 20 litres per hour Version L 5 bar / 10 litres per hour 8 bar / 8 litres per hour 10 bar / 5 litres per hour 15 bar / 4 litres per hour 18 bar / 2 litres per hour Version M 2 bar / 18 litres per hour 2. hidden in the "code" on the type plate you will find the reference to the pump head mounted at delivery and its sealing material. The ninth character indicates the sealing material. (see example picture of the type plate in the article) The most common types are listed below and these are shown via our selection matrix: K = PVDF pump head with Viton seal D = PP pump head with EPDM seal A = PMMA pumphead with Viton seal R = PMMA pumphead with EPDM seal Z = Stainless steel with Viton seal £ = Stainless steel pump head with EPDM gasket  (other types are available on request) Service set contents: PVDF pump head with Viton seal:1x pump head (dosing head) incl. seal 1x PTFE diaphragm- Stainless steel screws and caps (only for L and M service set) PP pump head with EPDM seal:1x pump head (dosing head) incl. seal  1x PTFE diaphragm - Stainless steel screws and caps (only for L and M service set)PMMA pump head with Viton or EPDM seal:1x pump head (dosing head) incl. seal 1x PTFE diaphragm - Stainless steel screws and caps (only for L and M service set) *Stainless steel pump head with Viton or EPDM seal:1x seal without pump head (no change required as stainless steel) 1x PTFE diaphragm frequently asked questions Is this service kit compatible with my emec K-Plus pump? Yes, if your pump is size ‘I’. You can check this on the pump’s type plate. What does the service kit contain? You will receive a new pump head with a seal, as well as a suitable diaphragm for replacement. When should I replace the service kit? If the pump’s performance has deteriorated, it’s leaking, or it hasn’t been serviced for a long time. Can I carry out the replacement myself? Many customers replace the pump head and diaphragm themselves. With a bit of DIY skill, it’s usually a quick job. How can I tell if my diaphragm or seal is worn out? Typical signs include dripping from the pump head, uneven flow or a loss of pressure. Why is it worth replacing the parts rather than buying a new pump? With the service kit, you can quickly restore your pump to a reliable working condition.