HORIBA Salinity Replacement Electrodes – Permanently Stable Evaluation of Salt Content and System Conditions

The HORIBA LAQUAtwin Pocket Tester series provides a comprehensive solution for fast and precise measurement of water quality parameters directly in the field. To ensure these measurements remain reliable and accurate, regular monitoring of the sensors and, if necessary, replacement with spare sensors is crucial. These replacement sensors are tailor-made for the HORIBA LAQUAtwin series and cover a wide range of types for various measurements: pH, conductivity, salinity, redox (ORP), as well as ion-selective sensors for sodium, potassium, nitrate, calcium, and fluoride. Each sensor is designed to maximize user-friendliness and accuracy, which HORIBA is renowned for in water quality testing worldwide. HORIBA replacement sensors guarantee users that their devices consistently deliver optimal performance and precise measurements. Advantages of HORIBA Replacement Sensors Easy Replacement: Sensors can be exchanged quickly, allowing uninterrupted measurement. High Accuracy: Replacement sensors ensure precise and reliable results. Wide Measurement Range: Various sensor types are available to capture a broad spectrum of water quality parameters. Durability: Sensors are designed for long service life, even under challenging conditions. Sensor Replacement Instructions Follow these steps to replace the sensor and maintain the longevity and accuracy of your HORIBA LAQUAtwin Pocket Tester: Removing the Sensor Turn off the tester. Lift the sensor tip slightly and pull the sensor away from the device. Completely detach the sensor from the tester. Installing the Sensor Make sure the tester is turned off. Ensure the waterproof gasket is intact and clean. Attach the sensor to the tester so that hook “A” on the back of the device fits into hole “a” on the sensor tip. Make sure the waterproof gasket is not twisted. Important: After replacing the sensor, follow the instructions in the user manual of the respective tester to make the device ready for accurate measurements. This typically includes calibration and, if necessary, conditioning. How can I tell if my sensor is worn out? Check the sensor condition as follows: Perform a 2-point calibration. If an error occurs during calibration, this indicates that the sensor has deteriorated. In this case, the sensor should be replaced. Regular checks and timely replacement of sensors ensure the high quality and reliability of your water quality measurements with HORIBA LAQUAtwin Pocket Testers. Please note: The salt exchange sensors, both old and new, are not compatible with each other. Similarly, the conditioning solutions for the old and new versions are not compatible with the respective device variants. How can you tell if you have an older or a new device? If your Pocket Tester is marked ‘4-cell’, you have the latest version of this device. In this case, you will need the replacement sensors listed in the cross-selling section, as well as the standard and conditioning solutions. These have been specially optimised for the new Pocket Testers and are not suitable for older models. Manufacturer Part Nr. 3200459866

The HORIBA LAQUAtwin Pocket Testers provide a comprehensive solution for immediate and precise measurement of water quality parameters directly in the field. To ensure that these measurements remain reliable and accurate, it is important to regularly check the sensors and replace them with spare sensors if necessary. The replacement sensors developed for the HORIBA LAQUAtwin series cover various types for different measurements: pH, conductivity, salinity, redox (ORP), as well as ion-selective sensors for sodium, potassium, nitrate, calcium, and fluoride. All of these sensors are designed to maximize user-friendliness and precision, qualities for which HORIBA is globally recognized in water quality testing. HORIBA replacement sensors ensure that users’ devices consistently deliver optimal performance and accurate measurements. Advantages of HORIBA Replacement Sensors Easy Replacement: Sensors can be quickly exchanged, allowing measurements to continue without delay. High Precision: Replacement sensors ensure that results are exact and reliable. Wide Measurement Range: Various sensor types are available to capture a broad spectrum of water quality parameters. Durability: Sensors are designed for long service life, even under challenging conditions. Sensor Replacement Instructions To ensure the longevity and accuracy of your HORIBA LAQUAtwin Pocket Tester, please follow these instructions when replacing a sensor: Removing the Sensor Turn off the tester. Carefully detach the sensor from the device and lift the sensor tip. Completely separate the sensor from the tester so that the two components are no longer connected. Installing the Sensor Ensure the tester is turned off. Check that the waterproof gasket is clean and undamaged. Attach the sensor to the tester by inserting hook “A” on the back of the device into hole “a” on the sensor tip. Make sure the waterproof gasket is not twisted. Important: After replacing the sensor, it is essential to follow the steps in the user manual of the respective tester to make the device ready for accurate measurements. (These manuals are available with the products. Calibration and, if necessary, conditioning are usually required.) How can I check if my sensor shows signs of wear? Check the sensor condition as follows: Perform a 2-point calibration. If an error occurs during calibration, this indicates that the sensor has deteriorated. In this case, replacing the sensor is recommended. Regular checks and timely replacement of sensors are essential to ensure the high standards and reliability of water quality measurements performed with HORIBA LAQUAtwin Pocket Testers. Please note: The salt exchange sensors, both old and new, are not compatible with one another. Similarly, the conditioning solutions for the old and new versions are not compatible with the respective device variants. How can you tell whether you have an older or a newer device? If your Pocket Tester is marked ‘4-cell’, you have the latest version of this device. In this case, you will need the replacement sensors listed in the cross-selling section, as well as the standard and conditioning solutions. These have been specially optimised for the new Pocket Testers and are not suitable for the older models. Manufacturer Part Nr. 3200597237

HORIBA’s LAQUAtwin pocket testers offer a comprehensive solution for the immediate and accurate measurement of water quality parameters directly on site. To ensure that these measurements remain reliable and accurate in the future, it is important to check the sensors regularly and replace them with replacement sensors when necessary. The replacement sensors developed for the HORIBA LAQUAtwin series include various types for different measurements: pH, conductivity, salinity, redox (ORP), as well as ion-selective sensors for sodium, potassium, nitrate, calcium and fluoride. These sensors have all been developed with the aim of maximising the user-friendliness and precision for which HORIBA is renowned worldwide in water quality testing. HORIBA’s replacement sensors ensure that users’ instruments always deliver optimum performance and carry out precise measurements. Advantages of HORIBA replacement sensors: Easy replacement: As the sensors are easy to replace, they can be swapped out quickly, allowing measurements to resume without delay. High precision: Thanks to the replacement sensors, measurement results are accurate and reliable. Wide measurement range: Various sensor types are available to measure a wide range of water quality parameters. Durability: The sensors are designed to have a long service life, even under difficult conditions. Product features: 4-chamber salt sensor S074-4EC Replacement sensor for LAQUAtwin 4ECSalt-11 (item number: 896096) Requires a minimum sample volume of 0.12 ml Waterproof Salinity 0.0 to 100.0 g/l, 0.00 to 10.00 % Minimum sample volume required 0.12 ml Temperature sensor Integrated Operating temperature range 5 to 40 °C Note: The sensors for LAQUAtwin-Salt11 and LAQUAtwin-4ECSalt-11 are not compatible Instructions for replacing the sensor: To ensure the longevity and accuracy of your HORIBA LAQUAtwin Pocket Tester, please follow these instructions when replacing the sensor: Removing the sensor Switch off the meter. Carefully detach the sensor from the meter and lift the tip of the probe. Disconnect the sensor from the meter so that these two components are no longer connected. Fitting the sensor Switch off the meter. Ensure that the waterproof seal is clean and undamaged. Attach the sensor to the meter by inserting the hook ‘A’ on the back of the meter into the hole ‘a’ at the tip of the sensor. Ensure that the waterproof seal is not twisted. Important: After replacement, it is essential to follow the steps in the user manual for the relevant tester to ensure the meter is ready for accurate measurements. (These instructions are available for our products. Calibration and, where necessary, conditioning are usually required.) Question: How can I check whether my sensor is showing signs of wear? Answer: By checking the sensor’s condition, as explained in more detail below: Check the condition of the sensor by performing a 2-point calibration. If an error occurs during calibration, this indicates that the sensor has deteriorated. In this case, it would be advisable to replace the sensor. To ensure the high standards and reliability of water quality measurements taken with HORIBA LAQUAtwin Pocket testers, regular checks and timely replacement of the sensors are essential. Note: How can I tell if I have an old or new device? If your Pocket Tester is marked ‘4-cell’, you have the latest version of this device. In this case, you will need the replacement sensors listed in the cross-selling section, as well as the standard and conditioning solutions. These have been specially optimised for the new Pocket Testers and are not suitable for older models. Manufacturer’s item number: 3201079163