Jumo Outdoor Resistance Thermometer with Pt1000 in Two-Wire Circuit with Operating Temperature -50 to +90 °C JUMO Outdoor Resistance Thermometer Protection Class IP65 Type: 902520/15-361-1005-1/903 This resistance thermometer from JUMO is suitable for temperature measurements outdoors and in environments exposed to moisture. Equipped with a Pt1000 sensor in a two-wire circuit, a measuring range of -50 to +90 °C, and an IP65 cable gland, this version is designed for reliable outdoor temperature measurement in HVAC applications. This version is therefore intended for outdoor temperature measurements where the housing must be reliably protected against dust and moisture. Technical Data Version: Outdoor resistance thermometer Measuring insert: 1 x Pt1000 Circuit type: Two-wire circuit Transmitter: without Operating temperature: -50 to +90 °C Protection class: IP65 Special feature: Cable gland (IP65) Advantages and Technical Features of the JUMO Outdoor Resistance Thermometer well suited for outdoor temperature measurements IP65 protection class for increased housing protection requirements IP65 cable gland for protected cable entry Pt1000 sensor for compatible control and evaluation systems Unlike Pt100 versions, this model operates with 1 x Pt1000 in a two-wire circuit. This is especially useful when the connected control or evaluation system is designed for Pt1000 or when this sensor configuration is preferred. Since no transmitter is integrated, this version is well suited for applications where the sensor is connected directly to compatible evaluation or control systems. A practical advantage is the IP65 cable gland. It ensures protected cable entry and supports reliable sealing of the connection point. This is especially important for outdoor applications or technically demanding environments to ensure reliable measurement performance under changing environmental conditions. Typical Applications Outdoor temperature measurement on buildings Heating, ventilation, and air conditioning systems Technical outdoor areas Weather-exposed measuring points Frequently Asked Questions Can I use the thermometer outdoors? Yes, it was specifically designed for both indoor and outdoor use. What temperature range is the thermometer suitable for? It reliably measures temperatures from -50°C to +90°C. What are the benefits of the IP65 rating? It protects the device against dust and water jets. Can I also use the thermometer in air ducts? Yes, it is suitable for temperature monitoring in air ducts. Is the thermometer suitable for heating and air conditioning systems? Yes, it is frequently used in heating, ventilation, and air conditioning systems. Can I connect the sensor directly to my control system? Yes, it is designed for direct connection to compatible systems. Where is this thermometer typically used? For example, in buildings, outdoor areas, and HVAC systems.

JUMO resistance thermometer for temperature measurements in indoor and outdoor areas as well as air ducts in the measuring range -50 to +90 °C JUMO room, outdoor and duct resistance thermometer IP65 protection class Type: 902520/15-361-1003-1/000 The resistance thermometer with IP65 protection class is suitable for temperature measurements in indoor areas, outdoor environments and air ducts. This version is intended for measuring points that need to operate reliably not only indoors but also in more demanding environments. With a Pt100 in two-wire configuration, an operating range from -50 to +90 °C and IP65 protection class, this resistance thermometer is particularly suitable for HVAC applications where temperature must be measured in rooms, outdoor environments or air ducts. Technical Data Design: Room, outdoor and duct resistance thermometer Measuring insert: 1 x Pt100 Circuit type: Two-wire configuration Transmitter: none Operating temperature: -50 to +90 °C Protection class: IP65 Tolerance class: Class B Advantages and technical features of the JUMO resistance thermometer high IP65 protection class for more demanding environments suitable for rooms, outdoor areas and air ducts wide operating range from -50 to +90 °C robust design for changing environmental conditions The major advantage of this version lies in its higher protection class. IP65 makes it particularly suitable for installation locations where the housing needs better protection against dust and water jets. This makes it well suited for measuring points exposed to greater daily demands or technically more challenging environments than classic room sensors. A Pt100 sensor in two-wire configuration is used for temperature measurement. This proven version is suitable for many common temperature measurement tasks in HVAC applications. Since no transmitter is integrated, this variant is especially useful where the sensor should be connected directly to a suitable control or evaluation unit. The measuring range from -50 to +90 °C further extends the possible applications. This makes the version suitable not only for typical indoor temperatures but also for cooler or warmer environments as found in outdoor areas or air ducts. Typical Areas of Application room temperature measurement in HVAC applications outdoor temperature measurement temperature monitoring in air ducts heating, ventilation and air conditioning systems Frequently Asked Questions Can I use the thermometer outdoors? Yes, it was specifically designed for both indoor and outdoor use. What temperature range is the thermometer suitable for? It reliably measures temperatures from -50°C to +90°C. What are the benefits of the IP65 rating? It protects the device against dust and water jets. Can I also use the thermometer in air ducts? Yes, it is suitable for temperature monitoring in air ducts. Is the thermometer suitable for heating and air conditioning systems? Yes, it is frequently used in heating, ventilation, and air conditioning systems. Can I connect the sensor directly to my control system? Yes, it is designed for direct connection to compatible systems. Where is this thermometer typically used? For example, in buildings, outdoor areas, and HVAC systems.

JUMO resistance thermometer for temperature measurements in indoor and outdoor areas with operating temperature range -20 to +80 °C JUMO room and outdoor resistance thermometer without transmitter with IP54 protection class Type: 902520/11-635-1003-1/000 The resistance thermometer with IP54 protection class is suitable for temperature measurements in indoor and outdoor areas. With Pt100 in two-wire configuration and a measuring range from -20 to +80 °C, this version is designed for HVAC applications with increased protection requirements. This version is intended for temperature measurements where the device should be better protected against environmental influences than standard room sensors. With a Pt100 in two-wire configuration, an operating range from -20 to +80 °C and IP54 protection class, this resistance thermometer is particularly suitable for HVAC applications where temperatures must be measured reliably indoors or outdoors. Technical Data Design: Room and outdoor resistance thermometer Measuring insert: 1 x Pt100 Circuit type: Two-wire configuration Transmitter: none Operating temperature: -20 to +80 °C Protection class: IP54 Advantages and technical features of the JUMO resistance thermometer for indoor and outdoor measurements suitable for indoor and outdoor areas IP54 protection class for better protected installation locations suitable for temperatures from -20 to +80 °C proven Pt100 for classic temperature measurement tasks direct integration without integrated transmitter good solution for HVAC applications with changing environmental conditions more robust design than standard indoor sensors The main difference compared to simpler indoor variants is the more robust protection class. IP54 makes this version suitable for installation locations where dust or splash water may be present. This makes it well suited for applications where the sensor is used not only in protected indoor environments but also in more demanding surroundings. A Pt100 sensor in two-wire configuration is used for temperature measurement. This is a proven solution for many classic measurement tasks in HVAC applications. Since no transmitter is integrated, this variant is especially suitable for applications where the sensor should be connected directly to compatible evaluation or control technology. Typical Areas of Application room temperature measurement in HVAC applications outdoor temperature measurement on buildings technical indoor and outdoor environments heating, ventilation and air conditioning systems applications with increased protection requirements against dust and splash water Frequently Asked Questions Can I use the thermometer indoors and outdoors? Yes, it is suitable for temperature measurements both indoors and outdoors. What temperature range is the thermometer suitable for? It can reliably measure temperatures from -20°C to +80°C. What are the benefits of the IP54 protection rating? It offers additional protection against dust and splashing water during daily use. Is the thermometer suitable for heating and air conditioning systems? Yes, it is frequently used in heating, ventilation, and air conditioning (HVAC) systems. Can I connect the thermometer directly to my control system? Yes, it is designed for direct connection to compatible monitoring and control systems. Is the thermometer suitable for varying environmental conditions? Yes, it was developed for applications involving diverse environmental conditions. Where is this thermometer typically used? For example, on buildings, in technical rooms, in climate control systems, and in heating, ventilation, and air conditioning (HVAC) systems.

Room, outdoor and duct resistance thermometers  Measuring range from -30 to +80°C  Measuring insert 1x temperature sensor Pt100 in three-wire circuit  Transmitter: without  Protection class IP20   Suitabel for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 Class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.

JUMO Screw-in Resistance Thermometer with Connection Cable, Loose Screw Connection and Reduced Thermowell JUMO Screw-in Resistance Thermometer with Connection Cable, Loose Screw Connection and Reduced Thermowell, Type: 902050/30-380-1001-1-5,4-27,5-114-11-2500/316 This JUMO screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. The version with loose screw connection and reduced thermowell is particularly suitable for applications where compact dimensions, flexible installation and reliable temperature measurement are required. With 1x Pt100 in a three-wire circuit, silicone connection cable, M10x1 process connection, 27.5 mm installation length and additional kink protection, this version is designed for practical use in technical systems. Technical data Version: Screw-in resistance thermometer with connection cable, loose screw connection and reduced thermowell Measuring insert: 1x Pt100 Circuit type: Three-wire circuit Tolerance class: Class B according to DIN EN 60751 Connection cable: Silicone Temperature range: -50 to +200 °C Thermowell diameter: Reduced from 5.4 mm to 3.3 mm Installation length: 27.5 mm Process connection: M10x1 Connection cable end: Ferrules according to DIN 46228 Part 4 Connection cable length: 2500 mm Type addition: Kink protection hose Typical areas of application Wherever a compact design, flexible screw connection and reliable temperature measurement are required, this version is a suitable choice. Air conditioning and refrigeration technology Heating engineering, furnace construction and apparatus engineering Advantages and special features of the JUMO screw-in resistance thermometer Thanks to the thermowell reduced to 3.3 mm, this version is particularly interesting for installation situations with limited space or for measuring points where a slimmer tip is advantageous. At the same time, the loose screw connection allows the thermometer to be adapted more flexibly to the respective installation situation during mounting. This makes the version well suited for applications where a compact design must be combined with a secure process connection. Why should you choose this version from JUMO? This version is a good choice when proven and precise temperature measurement with Pt100 is required. The Pt100 used according to DIN EN 60751, Class B, is one of the established solutions in temperature measurement technology and is suitable for many technical applications. In combination with the three-wire circuit, line influences can be compensated more effectively, which supports the most precise possible temperature measurement during operation. The connection cable is also designed for practical use. The silicone cable is suitable for temperatures from -50 to +200 °C and therefore offers good conditions for applications with low or elevated ambient temperatures. With a cable length of 2500 mm, there is also sufficient flexibility for connection to downstream evaluation or control technology. Ferrules according to DIN 46228 Part 4 simplify the electrical connection, while the additional kink protection relieves strain on the cable transition and makes the version more robust in everyday use. The compact installation length of 27.5 mm and the M10x1 process connection make this resistance thermometer particularly interesting for smaller and tighter measuring points. Especially where temperatures in liquid or gaseous media must be monitored reliably and space is limited at the same time, this version offers a practical solution. Type: 902050/30-380-1001-1-5,4-27,5-114-11-2500/316 Frequently Asked Questions Does the thermometer fit into tight installation spaces? Yes, its compact design and short insertion length make it well-suited for measurement points with limited space. For which media can I use the thermometer? The thermometer is designed for temperature measurement in liquid and gaseous media. Can the thermometer be mounted flexibly? Yes, the loose threaded fitting makes it easy to adapt to various installation situations. For which temperatures is the thermometer suitable? It can be used within a temperature range of -50 to +200 °C. Is the connection cable long enough for greater distances? Yes, the silicone connection cable is 2.5 meters long, offering sufficient flexibility during installation. Is the thermometer easy to connect? Yes, the connection cable is fitted with wire end ferrules, which simplifies the electrical connection. Where is this thermometer commonly used? Typical applications include HVAC and refrigeration technology, as well as heating, furnace, and equipment manufacturing. Is this thermometer compatible with my system? Yes, it is suitable for many industrial applications and can be flexibly integrated into various systems. How is the thermometer mounted? It is simply screwed in. The loose threaded fitting facilitates adjustment during installation. Can the thermometer be used in challenging environments? Yes, the protective thermowell reliably shields the sensor from external influences.

JUMO Screw-in Resistance Thermometer with Connection Cable and Loose Screw Connection JUMO Screw-in Resistance Thermometer with Connection Cable and Loose Screw Connection, Type: 902050/20-402-1003-1-6-37-114-11-2500/315,317 This screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. With metal braided connection cable, loose screw connection, 1x Pt100 in a two-wire circuit, 6 mm thermowell diameter, 37 mm installation length and M10x1 process connection, shielded version and high temperature measuring ranges up to +400 °C, this version is particularly suitable for compact measuring points and applications with increased temperature requirements. Technical data Version: Screw-in resistance thermometer with connection cable and loose screw connection Measuring insert: 1x Pt100 Circuit type: Two-wire circuit Tolerance class: Class B according to DIN EN 60751 Connection cable: Metal braid Temperature range: -50 to +400 °C Thermowell diameter: 6 mm Installation length: 37 mm Process connection: M10x1 Connection cable end: Ferrules according to DIN 46228 Part 4 Connection cable length: 2500 mm Type additions: Kink protection spring, shielded connection cable Typical areas of application Temperature measurement in cartridge heaters, heating blocks or heated components Temperature monitoring in pipelines, tanks and apparatus Applications in dry and humid environments Use in higher ambient temperatures General industrial and process applications Advantages and special features of this JUMO screw-in resistance thermometer A clear advantage of this version lies in the combination of robust construction and high temperature resistance. The metal braided connection cable is designed for temperatures from -50 to +400 °C and is therefore interesting for applications where standard cables are not sufficient. In addition, the shielded connection cable supports interference-free signal transmission, which can be particularly advantageous in technical and industrial environments. Why should you choose this version from JUMO? This version is a good choice when a compact resistance thermometer for higher temperature measuring ranges is required. The Pt100 used according to DIN EN 60751, Class B, is one of the proven standards in temperature measurement technology and is suitable for many typical measuring tasks. The two-wire circuit makes this version a practical solution for applications where reliable temperature measurement is the main focus. The mechanical design is also tailored for practical use. The loose screw connection allows flexible adjustment during installation, while the M10x1 process connection and the installation length of 37 mm make this version particularly interesting for smaller or confined measuring points. This allows the thermometer to be integrated well into technical systems where temperatures must be monitored permanently. Frequently Asked Questions Does the thermometer fit into tight installation spaces? Yes, its compact design makes it well-suited for small and confined measuring points. What temperature range is the thermometer suitable for? It can be used within a temperature range of -50 to +400°C. In what types of systems can I use the thermometer? It is suitable for pipelines, vessels, and technical systems across many sectors. Can the thermometer be mounted flexibly? Yes, the loose screw connection makes adjustment during installation easier. Is the thermometer suitable for industrial environments? Yes, its robust design is engineered for demanding technical applications. How is the thermometer connected? The connecting cable is fitted with wire ferrules, making it easy to connect. Why is this model particularly reliable? The shielded cable and the Pt100 sensor ensure stable and accurate readings. Is the thermometer suitable for liquids and gases? Yes, this JUMO screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. How long is the connecting cable? The connecting cable is 2.5 meters long. What material is the connecting cable made of? The connecting cable features a metal braid.

JUMO Screw-in Resistance Thermometer with Pt100 in Three-wire Circuit, M10x1 Process Connection and Shielded Version for Compact Measuring Points and High Temperatures up to +400 °C. JUMO Screw-in Resistance Thermometer with Connection Cable and Loose Screw Connection, Type: 902050/20-402-1001-1-6-37-114-11-2500/315,317 This JUMO screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. In this version, it is equipped with 1x Pt100 in a three-wire circuit, a metal braided connection cable, loose screw connection, 6 mm thermowell diameter, 37 mm installation length and M10x1 process connection. This makes the version particularly suitable for compact measuring points and applications with increased temperature requirements. Technical data Version: Screw-in resistance thermometer with connection cable and loose screw connection Measuring insert: 1x Pt100 Circuit type: Three-wire circuit Tolerance class: Class B according to DIN EN 60751 Connection cable: Metal braid Temperature range: -50 to +400 °C Thermowell diameter: 6 mm Installation length: 37 mm Process connection: M10x1 Connection cable end: Ferrules according to DIN 46228 Part 4 Connection cable length: 2500 mm Type additions: Kink protection spring, shielded connection cable Typical areas of application Air conditioning and refrigeration technology Heating engineering, furnace construction and apparatus engineering Wherever temperature measurements are required in pipelines, tanks, machines and technical systems In compact measuring points in liquid and gaseous media Special features and advantages of this JUMO screw-in resistance thermometer An advantage of this version lies in the combination of compact design and high temperature resistance. The metal braided connection cable is designed for temperatures from -50 to +400 °C and is therefore suitable for applications where standard cables are not sufficient. In addition, the shielded connection cable supports interference-free signal transmission, which can be particularly advantageous in technical and industrial environments. The mechanical design is also tailored for practical use. The loose screw connection allows flexible adjustment during installation, while the M10x1 process connection and the installation length of 37 mm make this version particularly interesting for smaller or confined measuring points. This allows the thermometer to be integrated well into technical systems where temperatures must be monitored permanently. The additional type addition with kink protection spring relieves strain on the cable transition and makes this version even more robust under mechanical stress. Especially in applications where movement, tension or frequent handling play a role, this is a practical advantage. Why should you choose this version from JUMO? This version is a good choice when precise Pt100 temperature measurement with improved compensation of line influences is required. The Pt100 used according to DIN EN 60751, Class B, is one of the proven standards in temperature measurement technology and is suitable for many typical measuring tasks. The three-wire circuit offers advantages when measured values need to be recorded more accurately than with a simple two-wire circuit. Type: 902050/20-402-1001-1-6-37-114-11-2500/315,317 Frequently Asked Questions Does the thermometer fit into tight installation spaces? Yes, its compact design makes it well-suited for small and confined measuring points. What temperature range is the thermometer suitable for? It can be used within a temperature range of -50 to +400°C. In what types of systems can I use the thermometer? It is suitable for pipelines, vessels, and technical systems across many sectors. Can the thermometer be mounted flexibly? Yes, the loose screw connection makes adjustment during installation easier. Is the thermometer suitable for industrial environments? Yes, its robust design is engineered for demanding technical applications. How is the thermometer connected? The connecting cable is fitted with wire ferrules, making it easy to connect. Why is this model particularly reliable? The shielded cable and the Pt100 sensor ensure stable and accurate readings. Is the thermometer suitable for liquids and gases? Yes, this JUMO screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. How long is the connecting cable? The connecting cable is 2.5 meters long. What material is the connecting cable made of? The connecting cable features a metal braid.

JUMO Screw-in Resistance Thermometer with Threaded Thermowell for Precise Temperature Measurement in Liquid and Gaseous Media JUMO Screw-in Resistance Thermometer with Connection Cable and Threaded Thermowell, Type: 902050/40-390-1003-1-8-25-111-11-2500/315,317 This screw-in resistance thermometer with connection cable and threaded thermowell is designed for precise temperature measurement in liquid and gaseous media. With its 1x Pt100 in a two-wire circuit, metal braided connection cable, 25 mm installation length, M8 process connection and shielded connection cable, this version is particularly suitable for compact installation situations and applications with increased requirements for temperature resistance and signal transmission. Advantages and special features of this JUMO screw-in resistance thermometer A major advantage of this version is its robust design for more demanding operating conditions. The metal braided connection cable is designed for temperatures from -50 to +300 °C and therefore offers excellent conditions for applications where standard cables reach their limits. At the same time, the shielded cable supports interference-free signal transmission, which can be a practical advantage especially in technical and industrial environments. Why should you choose this version from JUMO? This version is a good choice when a compact resistance thermometer with high temperature resistance and proven Pt100 measurement technology is required. The Pt100 used according to DIN EN 60751, Class B, is one of the established solutions in temperature measurement technology and is suitable for many common applications. The two-wire circuit makes this version a classic and practical solution for numerous measuring tasks. The mechanical design is also tailored for practical use. The M8 process connection and the 25 mm installation length make this thermometer particularly interesting for smaller measuring points or confined installation situations. The combination of threaded thermowell and compact design ensures that the version can be integrated well into technical systems where temperatures must be monitored reliably and permanently. In addition, the type addition with kink protection spring helps relieve strain on the cable transition. This special feature makes the version even more robust when the connection cable is subject to mechanical stress or when movement and tensile loads occur during operation. Typical areas of application Air conditioning and refrigeration technology Heating engineering, furnace construction and apparatus engineering Wherever temperatures in liquid or gaseous media must be measured precisely and at the same time a compact, temperature-resistant design is required, this version is a suitable choice. Technical data Version: Screw-in resistance thermometer with connection cable and threaded thermowell Measuring insert: 1x Pt100 Circuit type: Two-wire circuit Tolerance class: Class B according to DIN EN 60751 Connection cable: Metal braid Temperature range: -50 to +300 °C Thermowell diameter: M8 Installation length: 25 mm Process connection: M8 Connection cable end: Ferrules according to DIN 46228 Part 4 Connection cable length: 2500 mm Type additions: Kink protection spring, shielded connection cable Frequently Asked Questions Does the thermometer fit into small installation spaces? Yes, its compact design and short insertion length make it well-suited for confined installation areas. For which applications can I use the thermometer? It is suitable for measuring the temperature of liquid and gaseous media in technical systems. Is the thermometer suitable for high temperatures? Yes, it can be used within a temperature range of -50 to +300 °C. Can I use the thermometer in humid environments? Yes, it is designed for both dry and humid environments. Is the connection cable long enough for greater distances? Yes, the connection cable is 2.5 meters long, providing sufficient flexibility during installation. Is the thermometer easy to connect? Yes, the connection cable is fitted with wire end ferrules, making connection easier. Why is the thermometer suitable for industrial systems? The robust connection cable and shielded design ensure reliable operation in everyday use.

JUMO Screw-in Resistance Thermometer with Connection Cable and Threaded Thermowell JUMO Screw-in Resistance Thermometer with Connection Cable and Threaded Thermowell, Type: 902050/40-390-1001-1-8-25-111-11-2500/315,317 The JUMO screw-in resistance thermometer with Pt100 in a three-wire circuit, metal braided connection cable, M8 process connection and shielded version is particularly suitable for compact measuring points and higher temperature ranges up to +300 °C. This screw-in resistance thermometer is designed for precise temperature measurement in liquid and gaseous media. With 1x Pt100 in a three-wire circuit, metal braided connection cable, installation length of 25 mm, M8 process connection and shielded connection cable, this version is particularly suitable for compact measuring points and applications with increased requirements for temperature resistance and signal transmission. Typical areas of application Measuring points in liquid and gaseous media Dry and humid environments Compact or confined installation situations Applications with vacuum or overpressure Technical systems with increased requirements for the connection cable Technical data Version: Screw-in resistance thermometer with connection cable and threaded thermowell Measuring insert: 1x Pt100 Circuit type: Three-wire circuit Tolerance class: Class B according to DIN EN 60751 Connection cable: Metal braid Temperature range: -50 to +300 °C Thermowell diameter: M8 Installation length: 25 mm Process connection: M8 Connection cable end: Ferrules according to DIN 46228 Part 4 Connection cable length: 2500 mm Type additions: Kink protection spring, shielded connection cable Advantages and special features of the JUMO screw-in resistance thermometer This version shows its strengths especially under more demanding operating conditions. The metal braided connection cable is designed for temperatures from -50 to +300 °C and therefore offers excellent conditions for applications where standard cables are not sufficient. At the same time, the shielded connection cable supports interference-free signal transmission, which can be a practical advantage especially in technical and industrial environments. Why should you choose this version from JUMO? This version is a good choice when a compact resistance thermometer with proven Pt100 measuring technology and improved compensation of line influences is required. The Pt100 used according to DIN EN 60751, Class B, is one of the established solutions in temperature measurement technology and is suitable for many common applications. The three-wire circuit offers advantages compared to a simple two-wire circuit when measured values need to be recorded as precisely as possible. The mechanical design is also tailored for practical use. The M8 process connection and the installation length of 25 mm make this thermometer particularly interesting for smaller measuring points or confined installation situations. The compact design ensures that the version can be integrated well into technical systems where temperatures must be monitored reliably and permanently. Frequently Asked Questions Does the thermometer fit into small installation spaces? Yes, its compact design and short insertion length make it well-suited for confined installation areas. For which applications can I use the thermometer? It is suitable for measuring the temperature of liquid and gaseous media in technical systems. Is the thermometer suitable for high temperatures? Yes, it can be used within a temperature range of -50 to +300 °C. Can I use the thermometer in humid environments? Yes, it is designed for both dry and humid environments. Is the connection cable long enough for greater distances? Yes, the connection cable is 2.5 meters long, providing sufficient flexibility during installation. Is the thermometer easy to connect? Yes, the connection cable is fitted with wire end ferrules, making connection easier. Why is the thermometer suitable for industrial systems? The robust connection cable and shielded design ensure reliable operation in everyday use.

Screw-in resistance thermometer with connection head form J with stepped protection tube for air measurement Measuring range from -50 to +200 °C Single resistance thermometer 1x Pt 100 in two-wire circuit Tolerance class: Class B (standard) Thermowell diameter: 6 mm Installation length: 75 mm Process connection: G1/2 threaded connection Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure. The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head.

JUMO Dtrans T100 screw-in RTD temperature probe without transmitter, M12 x 1 machine plug connection Measuring range from -50 to + 200 °C 1x Pt100 in four-wire circuit Tolerance class: Class B (standard) Thermowell diameter: 6 mm Installation length: 100 mm Process connection: G1/2 screw connection Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: without M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC).

UMO Dtrans T100 screw-in RTD temperature probe with programmable transmitter, M12 x 1 machine plug connection Measuring range from -50 to + 150 °C 1x Pt1000 in four-wire circuit Tolerance class: Class A Thermowell diameter: 6 mm Installation length: 50 mm Process connection: without Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: without M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC).

Screw-in resistance thermometer with form J connection head  With continuous protection tube Measuring range from -50 to +200 °C Single resistance thermometer 2x Pt 100 in two-wire circuit Tolerance class: Class B (standard) Thermowell diameter: 6 mm Installation length: 50 mm Process connection: screw connection G ½ Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity

Typical areas of applicationindustrial and municipal, general water and waste water engineeringProcess measurements, electroplating, final inspections, neutralisation plantsdrinking and well water, boiler feed waterlightly contaminated waste waterDouble-chamber design in the presence of electrode poisons (e.g. sulphides, cyanides)low-temperature applications (-30 ... +30 °C), e.g. measurement in cooling systemsFluoride-containing (hydrofluoric acid) media up to 1000 mg/l HFHigh-alkali applications (reduced alkali error at pH values > pH 12)Special featuresHigh-quality zirconium dioxide diaphragm (glass fibre diaphragm with plastic shaft)Cartridge discharge system with silver ion-free reference electrolytepressure-resistant versions up to 10 bar (50 °C)Temperature range: up to -5 ... +80 °C (90 °C for ORP) or -30 ... +30 °C (with TT version)Temperature sensors can be integrated as an optionoptional salt reserve to increase the service life in media with lower conductivity or in drinking waterJUMO HA glass for continuous measurements in the range up to pH 14ORP versions with platinum or gold tip up to ±2000 mV

These amperometric sensors with membrane are used to determine the concentration of free chlorine. They are able to measure various inorganic chlorine compounds, including chlorine gas (Cl₂), electrolytically generated chlorine, sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂) and chlorinated lime (Ca(OCl)Cl). Testing for the complete absence of free chlorine is not possible with these sensors. Depending on the version, the sensors either supply a temperature-compensated current signal (4-20 mA) in an analogue version or a Modbus RTU signal via a digital interface. Calibration takes place in a downstream device such as an indicator, controller, recorder or programmable logic controller (PLC). The sensors can be connected directly to various transmitters or controllers. These supply the system with the required voltage and enable uncomplicated calibration. Areas of application: The sensors are used to measure free chlorine in drinking water, bathing water, industrial water, process water and cooling water. Frequently Asked Questions Was macht dieses Produkt so besonders? It measures the chlorine level in the water to monitor water quality. Wo wird das Produkt eingesetzt? It is suitable for monitoring free chlorine in water, for example in swimming pools or drinking water systems. Kann ich das Produkt dauerhaft nutzen? Yes. The sensor takes continuous measurements and is suitable for continuous operation. Ist der Sensor für Schwimmbäder geeignet? Yes. It is specifically designed for monitoring chlorine in swimming pool water. Wie wird der Messwert ausgegeben? Depending on the version, as a 4–20 mA signal or digitally via Modbus RTU. Muss ich den Sensor direkt am Gerät kalibrieren? No. Calibration is performed via external devices such as controllers or control systems. In welche Systeme lässt sich der Sensor integrieren? It can be easily integrated into existing measurement and control systems. Für welche Wasserarten ist der Sensor geeignet? For drinking water, process water, cooling water, and other applications involving chlorinated water.

Brief description The high-quality materials and components of the JUMO tecLine HD electrodes make them particularly suitable for the most demanding applications in process and industrial measurement technology. They are combined combination electrodes (with a reference electrode and a glass or metal electrode in a shaft).Depending on the design, it is possible to integrate an additional Pt1000 temperature sensor.Insensitive to large amounts of dirt as well as processes and waste water rich in oil and grease. For processes with a high solids content (e.g. waste water with sand particles or media that are subject to precipitation or crystallisation reactions), a perforated diaphragm variant is available as the optimum solution. JUMO tecLine HD electrodes represent the latest technology for pH and redox electrodes. Each electrode is a high-quality product that is individually unit-tested and comes with a calibration certificate. Modern production facilities guarantee constant values.All conventional electrodes are made from physiologically safe and FDA-listed materials.Their shaft glass is lead-free and therefore RoHS 2 compliant. Translated with DeepL.com (free version)

Typical areas of applicationProcesses with higher continuous temperatures (up to a maximum of 135 °C)Sterilisation applicationsDouble chamber design in the presence of electrode poisonsfluoride-containing (hydrofluoric acid-containing) media up to 1000 mg HF/lSpecial featuresproven JUMO HT glass (pH high-temperature membrane glass) 0 ... 14 pHJUMO DS membrane glass for sterilization applicationsCartridge discharge system with silver ion-free reference electrolyte (gel)Pressure-resistant versions up to 10 bar (50 °C)Temperature range: 0 ... 135 °C1Temperature sensors can be integrated as an optionORP versions with platinum or gold cap up to ±2000 mV

Thanks to the salt reservoir, this version is particularly suitable for applications with low-ion media or higher flow rates, where an extended electrode service life is beneficial. JUMO tecLine pH electrode with salt reservoir, UW glass, PTFE ring diaphragm, S8 Pg13.5 screw head, 120 mm (Type code: 201020/51-18-04-22-120/837; Part No.: 321035) This JUMO tecLine pH electrode is a good choice when a reliable and durable solution for pH measurement in aqueous media is required. With its salt reservoir design, this version is especially suitable for applications where the electrode is used under more demanding conditions and where maximum service life is required. Users looking for more than a standard pH electrode will benefit from a design focused on stable and long-term operation. Advantages and special features A key advantage of this electrode lies in the combination of UW glass, PTFE ring diaphragm, and salt reservoir. The UW glass supports reliable pH measurement, while the PTFE ring diaphragm provides a robust solution for more demanding measurement conditions. The salt reservoir is particularly beneficial in applications where higher requirements are placed on electrode lifetime. This makes the design especially attractive for users who value a robust and long-lasting electrode for regular measurement tasks. Technical information With the S8 Pg13.5 screw head and a 120 mm insertion length, the electrode is suitable for many common installation situations. The glass shaft design makes it a classic solution for precise pH measurements in appropriate applications. Its well-balanced construction allows easy integration into existing measurement setups. Why choose this electrode? Because it is particularly suitable when a pH electrode is not only required to measure reliably but also to maintain long-term stability and durability in continuous operation. The salt reservoir makes this electrode especially attractive for conditions where extended service life is important. Combined with the PTFE ring diaphragm, it results in a robust and high-quality solution for users requiring dependable routine measurements. Applications The electrode is used for pH measurement in aqueous media. It is suitable wherever precise pH monitoring is required and where a salt reservoir provides additional benefit. This makes it a strong choice for applications where reliability, service life, and clean integration into the measurement point are important. Water treatment Drinking water monitoring Swimming pool technology Process water Surface water General laboratory and industrial measurement tasks

General descriptionThe electrodes are characterised by high mechanical and chemical resistance. Due to the stable PVDF body, there is practically no risk of the sensor breaking. The electrolyte of these combination electrodes guarantees a stable measured value, even in critical media containing sulphite.A Pt1000 temperature sensor is integrated. Depending on the application, the electrodes can be manufactured as pH or redox electrodes. An open annular gap diaphragm is used as the diaphragm.Areas of applicationChemical industryWaste water treatmentSewage treatmentPaper industry

Typical areas of applicationindustrial and municipal, general water and waste water engineeringProcess measurements, electroplating, final inspections, neutralisation plantsdrinking and well water, boiler feed waterlightly contaminated waste waterDouble-chamber design in the presence of electrode poisons (e.g. sulphides, cyanides)low-temperature applications (-30 ... +30 °C), e.g. measurement in cooling systemsFluoride-containing (hydrofluoric acid) media up to 1000 mg/l HFHigh-alkali applications (reduced alkali error at pH values > pH 12)Special featuresHigh-quality zirconium dioxide diaphragm (glass fibre diaphragm with plastic shaft)Cartridge discharge system with silver ion-free reference electrolytepressure-resistant versions up to 10 bar (50 °C)Temperature range: up to -5 ... +80 °C (90 °C for ORP) or -30 ... +30 °C (with TT version)Temperature sensors can be integrated as an optionoptional salt reserve to increase the service life in media with lower conductivity or in drinking waterJUMO HA glass for continuous measurements in the range up to pH 14ORP versions with platinum or gold tip up to ±2000 mV

Typical areas of applicationindustrial waste water technologyprocess measurements, electroplating, paper industry, beverage industryoily waste watersuspensions, lacquers, media with solid particlesDouble-chamber design in the presence of electrode poisonsFluoride-containing (hydrofluoric acid-containing) media up to 1000 mg/l HFSpecial featuresDirt-repellent PTFE ring diaphragm with highly viscous KCl solution (gel) or perforated or annular gap diaphragm with polymerised solid electrolyte - practically blockage-freeCartridge discharge system with silver ion-free reference electrolytePressure-resistant versions up to 10 bar (50 °C)Temperature range: see order detailsOptional temperature sensors can be integratedOptional salt reservoir to increase service life in media with low conductivity

JUMO Wall-Mounted Resistance Thermometer with Pt100 in Two-Wire Circuit and Operating Temperature -30 to +90 °C JUMO Wall-Mounted Resistance Thermometer with Internal Sensor Protection Class IP65 Type: 902520/21-573-1003-1/000 The wall-mounted resistance thermometer is suitable for temperature measurements in HVAC applications with increased protection requirements. Equipped with a Pt100 sensor in a two-wire circuit, a measuring range of -30 to +90 °C, and protection class IP65, this version is designed for compact wall-mounted measuring points in indoor and protected outdoor areas. This version is intended for wall-mounted temperature measurements and is especially useful where the sensor is protected inside the housing while requiring a robust outer enclosure. Technical Data Version: Wall-mounted resistance thermometer with internal sensor Measuring insert: 1 x Pt100 Circuit type: Two-wire circuit Transmitter: without Operating temperature: -30 to +90 °C Protection class: IP65 Advantages and Technical Features of the JUMO Wall-Mounted Resistance Thermometer compact wall mounting with integrated internal sensor IP65 protection class for increased housing protection requirements closed design without protruding sensing element Pt100 sensor for proven temperature measurement suitable for temperatures from -30 to +90 °C direct integration without integrated transmitter well suited for HVAC applications with increased protection requirements The internal sensor makes this version particularly interesting for measuring points where the temperature is to be recorded directly in the area surrounding the housing without requiring a protruding sensing element. This can be advantageous wherever a compact, closed design is preferred and the sensor should remain better protected against mechanical influences. With protection class IP65, this version provides significantly greater protection against dust and water than standard room sensors. This makes it suitable for environments where the housing is exposed to higher levels of stress or where a higher protection rating is required. Especially in HVAC technology, this can be beneficial for installations in more technically demanding environments. Temperature measurement is performed using a Pt100 sensor in a two-wire circuit. This proven sensor configuration is suitable for many standard measurement tasks in temperature measurement technology. Since no transmitter is integrated, this version is particularly well suited for applications where the sensor is connected directly to a suitable control or evaluation unit. Typical Applications Wall mounting in HVAC applications Temperature monitoring in technical indoor areas Protected outdoor areas Applications with increased protection requirements against dust and water Heating, ventilation, and air conditioning systems Frequently Asked Questions What can I use this thermometer for? It is ideal for rooms, equipment, or processes where temperature monitoring is required. Can I use the thermometer in damp areas? Yes; thanks to its IP65 rating, the housing is well-protected against dust and water, making it suitable for more demanding environments. Is the device suitable for outdoor use? Yes, it can be used in sheltered outdoor areas, such as under canopies or in weather-protected technical areas. What temperature range is the thermometer suitable for? The device reliably measures temperatures from -30 to +90°C, covering a wide range of applications. Where exactly is the temperature measured? The sensor is housed securely within the casing and measures the temperature in the immediate vicinity of the mounting point. Is the thermometer suitable for my heating or ventilation system? Yes, it is frequently used for temperature monitoring in heating, ventilation, and air conditioning (HVAC) systems. Do I need an additional transmitter? No, the thermometer outputs a Pt1000 signal directly and can be connected to compatible evaluation or control systems. Why doesn't the device have a protruding probe? The enclosed design protects the sensor and allows for compact, unobtrusive wall mounting. Can I use it outdoors or in damp areas? Yes; thanks to its IP65 rating, it is dust-tight and protected against water jets. How robust is the thermometer for everyday use? It is durable, shock-resistant, and suitable for continuous operation.

Wall-Mounted Resistance Thermometer by JUMO with Pt1000 in Two-Wire Circuit and Operating Temperature -30 to +90 °C JUMO Wall-Mounted Resistance Thermometer with Internal Sensor Protection Class IP65 Type: 902520/21-573-1005-1/000 This wall-mounted resistance thermometer from JUMO is suitable for HVAC temperature measurements with a compact housing design. Equipped with Pt1000 in a two-wire circuit and a measuring range of -30 to +90 °C, this version is designed for wall-mounted measuring points in indoor and protected outdoor areas. This version is suitable for wall-mounted measuring points where the sensor should be protected inside the housing while a Pt1000 signal is required. With an operating range of -30 to +90 °C and protection class IP65, this wall-mounted resistance thermometer is particularly suitable for HVAC applications in indoor and protected outdoor areas. Technical Data Version: Wall-mounted resistance thermometer with internal sensor Measuring insert: 1 x Pt1000 Circuit type: Two-wire circuit Transmitter: without Operating temperature: -30 to +90 °C Protection class: IP65 Advantages and Technical Features of this JUMO Thermometer Version compact wall mounting with integrated internal sensor IP65 protection class for increased housing protection requirements closed design without protruding sensing element Pt1000 sensor for compatible control and evaluation systems suitable for temperatures from -30 to +90 °C direct integration without integrated transmitter well suited for HVAC applications with increased protection requirements The internal sensor makes this version especially interesting wherever the temperature should be measured directly around the housing without requiring a separate protruding sensing element. This creates a compact design and is particularly practical where a discreet, closed solution is preferred. Unlike Pt100 versions, this model operates with 1 x Pt1000 in a two-wire circuit. This is particularly useful when the connected control or evaluation system is designed for Pt1000 or when this sensor configuration is preferred. Since no transmitter is integrated, the device is especially suitable for applications where the sensor should be connected directly to a compatible evaluation unit. With protection class IP65, the housing is well protected against dust and water. This makes the version suitable for environments where standard room sensors are not sufficient and a more robust housing is required. Especially in HVAC technology, this can be an advantage for wall-mounted installations in technically demanding areas. Typical Applications Wall mounting in HVAC applications Temperature monitoring in technical indoor areas Protected outdoor areas Heating, ventilation, and air conditioning systems Frequently Asked Questions What can I use this thermometer for? It is ideal for rooms, equipment, or processes where temperature monitoring is required. Can I use the thermometer in damp areas? Yes; thanks to its IP65 rating, the housing is well-protected against dust and water, making it suitable for more demanding environments. Is the device suitable for outdoor use? Yes, it can be used in sheltered outdoor areas, such as under canopies or in weather-protected technical areas. What temperature range is the thermometer suitable for? The device reliably measures temperatures from -30 to +90°C, covering a wide range of applications. Where exactly is the temperature measured? The sensor is housed securely within the casing and measures the temperature in the immediate vicinity of the mounting point. Is the thermometer suitable for my heating or ventilation system? Yes, it is frequently used for temperature monitoring in heating, ventilation, and air conditioning (HVAC) systems. Do I need an additional transmitter? No, the thermometer outputs a Pt1000 signal directly and can be connected to compatible evaluation or control systems. Why doesn't the device have a protruding probe? The enclosed design protects the sensor and allows for compact, unobtrusive wall mounting. Can I use it outdoors or in damp areas? Yes; thanks to its IP65 rating, it is dust-tight and protected against water jets. How robust is the thermometer for everyday use? It is durable, shock-resistant, and suitable for continuous operation.