JUMO 25 meter connection cable (4-wire + shield)

If you are looking for a conductive 2-electrode conductivity sensor for typical water and industrial applications and value K = 0.1, integrated Pt100, G 3/4" A threaded connection, PVC body, and stainless steel 1.4571, this JUMO ecoLine CR-PVC version is an excellent choice. JUMO ecoLine CR-PVC conductivity sensor with cell constant K = 0.1, Pt100, threaded connection G 3/4" A, PVC body, and stainless steel 1.4571 cell material This CR-PVC conductivity sensor is designed for conductive conductivity measurement in water and process applications. It operates according to the proven 2-electrode principle and is particularly suitable for applications where reliable conductivity measurement in the low measuring range is required. Thanks to the design with cell constant K = 0.1, integrated Pt100, threaded connection G 3/4" A, PVC body, and stainless steel 1.4571 cell material, this version is tailored to typical tasks in water technology and industrial circulation systems. Technical data Measurement principle: Conductive 2-electrode conductivity sensor Cell constant: K = 0.1 Typical measuring range: 0 ... 1.0 mS/cm Temperature compensation: with Pt100 Process connection: Threaded connection G 3/4" A Body material: PVC Cell material: Stainless steel 1.4571 Operating temperature: up to 55 °C Maximum pressure: 6 bar at 25 °C Advantages and special features of the JUMO ecoLine A key advantage of this version lies in its suitability for measuring ranges up to 1.0 mS/cm. This makes it particularly interesting for applications in which lower conductivity values must be measured precisely. In the stainless steel version with K = 0.1, the sensor has three metallic pin electrodes. The two outer pins are electrically connected and form one pole of the 2-electrode conductivity sensor, while the central stainless steel pin serves as the counter electrode. According to your information, this design achieves high measurement precision and low stray fields. This makes the version particularly attractive for users who value clean and stable measurements. Why should you choose this conductivity sensor from JUMO? This version is particularly useful when a proven solution for industrial use is required that can measure not only conductivity but also temperature directly. The integrated Pt100 enables simultaneous measurement of the medium temperature, which is a clear advantage for temperature compensation in downstream measuring amplifiers. This is especially practical in applications where conductivity must be considered temperature-dependent. The PVC body limits use to medium temperatures up to 55 °C but offers a proven design for many typical water and process applications. The mechanical integration is also designed for practical use. The threaded connection G 3/4" A is one of the common connection sizes and is suitable for many standard installation situations. The sensor is designed for a maximum pressure of 6 bar at 25 °C and is therefore suitable for numerous industrial applications. Together with stainless steel 1.4571 as the cell material, this results in a robust and proven design for everyday use. Typical areas of application Areas of application include general water technology, cooling and air-conditioning technology, drinking and bathing water systems, as well as industrial rinsing and process water circuits. Wherever conductivity in the lower measuring range must be monitored reliably, this version is particularly interesting. Thanks to the combination of K = 0.1 and Pt100, the sensor is especially suitable for applications requiring precise conductivity measurement and simultaneous temperature detection.

If you are looking for a conductive 2-electrode conductivity sensor for typical water and industrial applications and value K = 0.1, integrated Pt100, PVC stepped collar Ø32/DN25, PVC body, and stainless steel 1.4571, this JUMO ecoLine CR-PVC version is an excellent choice. JUMO ecoLine CR-PVC conductivity sensor with cell constant K = 0.1, Pt100, PVC stepped collar Ø32/DN25, PVC body, and stainless steel 1.4571 cell material This JUMO ecoLine CR-PVC conductivity sensor is designed for conductive conductivity measurement in water and process applications. It operates according to the proven 2-electrode principle and is particularly suitable for applications where lower conductivity values must be measured reliably and precisely. Thanks to the design with cell constant K = 0.1, integrated Pt100, PVC stepped collar Ø32/DN25, PVC body, and stainless steel 1.4571 cell material, this version is tailored to typical tasks in water technology and industrial circulation systems. Technical data Measurement principle: Conductive 2-electrode conductivity sensor Cell constant: K = 0.1 Typical measuring range: 0 ... 1.0 mS/cm Temperature compensation: with Pt100 Process connection: PVC stepped collar Ø32/DN25 Body material: PVC Cell material: Stainless steel 1.4571 Operating temperature: up to 55 °C Maximum pressure: 6 bar at 25 °C Special features and advantages of the JUMO ecoLine A key advantage of this version lies in its suitability for measuring ranges up to 1.0 mS/cm. This makes it particularly interesting for applications where low conductivity values must be monitored reliably. In the stainless steel version with K = 0.1, the sensor has three metallic pin electrodes. The two outer pins are electrically connected and form one pole of the 2-electrode conductivity sensor, while the central stainless steel pin serves as the counter electrode. This design achieves high measurement precision and low stray fields. This makes the version particularly attractive for users who value stable and clean measurement values. The integration into the measuring point is also designed for practical use. The plug-in version with PVC stepped collar Ø32/DN25 is intended for use with suitable PVC T-pieces and allows quick removal of the sensor for cleaning or maintenance. This is a clear advantage during operation when the sensor needs to be removed without great effort. Together with stainless steel 1.4571 as the cell material, this results in a robust and proven design for everyday use. Why should you choose this conductivity sensor from JUMO? This version is particularly useful when a proven solution for industrial use is required that can measure not only conductivity but also temperature directly. The integrated Pt100 enables simultaneous measurement of the medium temperature, which is a clear advantage for temperature compensation in downstream measuring amplifiers. This is especially practical in applications where conductivity must be evaluated depending on temperature. The PVC body limits use to medium temperatures up to 55 °C and offers a proven design for many typical water and process applications. Typical areas of application Water technology Cooling and air-conditioning technology Drinking and bathing water systems as well as industrial rinsing and process water circuits This sensor is used wherever conductivity in the lower measuring range must be monitored reliably. Thanks to the combination of K = 0.1, Pt100, and the plug-in installation design, the sensor is especially suitable for applications requiring precise conductivity measurement, temperature detection, and easy maintenance.

If you are looking for a conductive 2-electrode conductivity sensor for typical water and industrial applications and value K = 1.0, integrated Pt100, PVC stepped collar Ø32/DN25, PVC body, and graphite, this JUMO ecoLine CR-PVC version is an excellent choice. JUMO ecoLine CR-PVC conductivity sensor with cell constant K = 1.0, Pt100, PVC stepped collar Ø32/DN25, PVC body, and graphite cell material This JUMO ecoLine CR-PVC conductivity sensor is designed for conductive conductivity measurement in water and process applications. It operates according to the proven 2-electrode principle and is particularly suitable for applications where conductivity values in an extended measuring range must be measured reliably. Thanks to the design with cell constant K = 1.0, integrated Pt100, PVC stepped collar Ø32/DN25, PVC body, and graphite as the cell material, this version is tailored to typical tasks in water technology and industrial circulation systems. Special features and advantages of the JUMO ecoLine A key advantage of this version lies in its typical measuring range from 0.01 to 15 mS/cm. This makes it particularly interesting for applications where higher conductivity values must be monitored reliably. In this version, graphite is used as the electrode material. The graphite electrodes are fully integrated into the electrode shaft and are especially suitable for the above-mentioned measuring ranges, where this design demonstrates its strengths particularly well. This makes the sensor a suitable solution for users requiring robust and practical conductivity measurement in industrial applications. The integration into the measuring point is also designed for practical use. The plug-in version with PVC stepped collar Ø32/DN25 is intended for use with suitable PVC T-pieces and allows quick removal of the sensor for cleaning or maintenance. This is especially practical during operation when the sensor needs to be removed without great effort. The delivery does not include a union nut. Why should you choose this conductivity sensor from JUMO? This version is particularly useful when, in addition to conductivity, the temperature must also be measured directly. The integrated Pt100 enables simultaneous measurement of the medium temperature and therefore provides the basis for temperature compensation in downstream measuring amplifiers. This is a clear advantage, especially in applications where conductivity changes with temperature. The PVC body limits use to medium temperatures up to 55 °C and offers a proven design for many typical water and process applications. Typical areas of application General water technology Cooling and air-conditioning technology, drinking and bathing water systems Industrial rinsing and process water circuits This sensor can be used wherever conductivity in a range from 0.01 to 15 mS/cm must be monitored reliably. Thanks to the combination of K = 1.0, Pt100, and the plug-in installation design, the sensor is especially suitable for applications requiring conductivity measurement, temperature detection, and easy maintenance. Technical data Measurement principle: Conductive 2-electrode conductivity sensor Cell constant: K = 1.0 Typical measuring range: 0.01 ... 15 mS/cm Temperature compensation: with Pt100 Process connection: PVC stepped collar Ø32/DN25 Note on scope of delivery: Delivered without union nut Body material: PVC Cell material: Graphite Operating temperature: up to 55 °C Maximum pressure: 6 bar at 25 °C Electrical connection: Connector according to DIN EN 175301-803 (Hirschmann connector)

JUMO DN25 PVC T-piece including union nut, O-ring, and solvent welding socket This JUMO DN25 PVC T-piece is the suitable accessory for installing a JUMO ecoLine CR-PVC 2-electrode conductivity sensor. It is supplied including a union nut, O-ring, and solvent welding socket and is designed for use in corresponding PVC piping systems. The DN25 version is particularly suitable for applications where the sensor must be integrated into the measuring point securely and practically. In combination with the plug-in sensor version, the T-piece allows easy installation as well as quick removal of the sensor for cleaning or maintenance. Especially during ongoing operation, this is a clear advantage when service work needs to be carried out as simply as possible. This PVC T-piece is therefore a useful addition for compatible JUMO ecoLine CR-PVC conductivity sensors whenever a clean and maintenance-friendly installation solution is required. Technical data Version: DN25 Material: PVC Scope of delivery: Union nut, O-ring, solvent welding socket Suitable for: JUMO ecoLine CR-PVC 2-electrode conductivity sensor Why is this T-piece from JUMO useful? If you want to integrate a compatible JUMO ecoLine CR-PVC conductivity sensor into a DN25 pipeline, this T-piece provides a suitable and practical installation solution. The complete scope of delivery with union nut, O-ring, and solvent welding socket simplifies installation and makes this accessory especially practical for new installations or replacements.

JUMO PVC T-piece DN32 incl. union nut, O-ring and adhesive socket JUMO PVC T-piece DN32 incl. union nut, O-ring and adhesive socket This JUMO PVC T-piece DN32 is the suitable accessory for installing a JUMO ecoLine CR-PVC 2-electrode conductivity sensor. It is supplied including a union nut, O-ring and adhesive socket and is available as a DN32 version. The JUMO T-piece DN32 is therefore a suitable accessory for selected ecoLine CR-PVC sensor variants. This version is particularly useful when the conductivity sensor needs to be integrated cleanly and practically into a suitable pipeline system. Thanks to the supplied mounting set, important components are already included, which simplifies installation and supports a maintenance-friendly installation solution. Especially in applications where the sensor must be cleaned regularly or removed for maintenance work, a suitable T-piece is a practical addition. This creates a suitable installation situation for the JUMO ecoLine CR-PVC 2-electrode conductivity sensor. Technical data Version: DN32 Material: PVC Scope of delivery: Union nut, O-ring, adhesive socket Suitable for: JUMO ecoLine CR-PVC 2-electrode conductivity sensor Why is this JUMO T-piece useful for the ecoLine? Anyone looking to integrate a suitable JUMO ecoLine CR-PVC conductivity sensor into a DN32 pipeline receives a practical and suitable installation solution with this T-piece. The complete scope of delivery simplifies installation and makes the accessory especially practical for new installations, retrofits or the replacement of existing components.

JUMO PVC T-piece DN40 JUMO PVC T-piece DN40 incl. union nut, O-ring and adhesive socket This JUMO PVC T-piece DN40 is the suitable accessory for installing a JUMO ecoLine CR-PVC 2-electrode conductivity sensor. The DN40 version is supplied including a union nut, O-ring and adhesive socket. The T-piece is particularly useful when the conductivity sensor needs to be integrated cleanly and practically into a suitable pipeline system. Thanks to the supplied accessory set, the necessary components for installation are already included, which simplifies installation and supports a maintenance-friendly installation situation. Technical data Version: DN40 Material: PVC Scope of delivery: Union nut, O-ring, adhesive socket Suitable for: JUMO ecoLine CR-PVC 2-electrode conductivity sensor Application of the JUMO T-piece for the ecoLine Especially in applications where the sensor must be removed again for cleaning or maintenance, a suitable T-piece is a practical addition. The DN40 version is a suitable accessory for JUMO ecoLine CR-PVC sensors. If you would like to integrate a JUMO ecoLine CR-PVC 2-electrode conductivity sensor into a DN40 pipeline, this T-piece provides a suitable and practical installation solution. The supplied union nut, O-ring and adhesive socket make the accessory especially practical for new installations, retrofits or the replacement of existing components.