The solenoid-operated metering pumps with vertical mounting are easy to install, cost-effective and reliable. Features:Digital systemMicroprocessor technologyConstantmA signal inputVolt signal inputBatch dosingOperation pause modeWater meter External contactMultifunction:ConstantDivideMultiplyInput:Level control water meterOutput:Alarm outputAccessories (selectable via the configurator):Suction lances:emec Viton suction lance with 40cm immersion length (with BNC connection)emec Viton suction lance with 122cm immersion length (with BNC connection)emec EPDM suction lance with 40cm immersion length (with BNC connection)emec EPDM suction lance with 122cm immersion length (with BNC connection)Scope of delivery:1x dosing pump 230 VAC with mains cable1x Injection valve 1/2" made of PVDF or PP, depending on the selected variant1x axial foot valve with level switch/empty indicator made of PVDF or PP, depending on the selected variant and 2.5 metre connection cable including BNC plug1x 2m pressure hose made of PVDF (for PVDF head) or PE (for PP head), 4x6mm, 4x8mm or 6x8mm* (depending on version, see technical data)1x 2m suction hose PVC transparent, 4x6mm, 4x8mm, 6x8mm* (depending on version, see technical data)1x 2m venting hose PVC transparent, 4x6mm
1x 2.5m "INPUT" connection cable with BNC plug and open cable ends1x instruction manual2x 3.5 x 40mm Phillips screws and 6mm dowels1x fine-wire fuse 5 x 20mm, T 1AOverview of operating modesCONSTANT - The dosing pump doses with an adjustable, constant dosing quantity. The quantity is set in l/h,
strokes/minute, or strokes/h (for very small dosing quantities). The pump is controlled either via the
digital input "INPUT" (which in this case has a start/pause or standby function), or via the power supply.
switched on and off via the power supply.DIVISOR - A pulse generator connected to the universal input "INPUT" (e.g. contact water meter) gives
pulses to the dosing pump in proportion to the water flow. These pulses are divided by the programmed
(divided) by the programmed value and thus determine the stroke frequency or the delivery rate.MULTIPLICATOR - A pulse generator (e.g. contact water meter) connected to the universal input "INPUT" sends pulses to the dosing pump proportional to the water flow.
pulses to the dosing pump in proportion to the water flow. These pulses are multiplied by the programmed
value and thus determine the stroke frequency or the delivery rate.PPM [mg/l] - A pulse generator (e.g. contact water meter) connected to the universal input "INPUT" sends pulses to the dosing pump proportional to the water flow.
pulses to the dosing pump in proportion to the water flow. With the pulses and the programmed
"PPM" value, the electronics calculate the stroke frequency for dosing proportional to the water flow. For this
the impulse rate of the contact water meter (in imp./ltr. or ltr./imp.), as well as the stroke volume
(depending on the local system pressure) must be set.PERCENT [%] - A pulse generator (e.g. contact water meter) connected to the universal input "INPUT" gives pulses to the dosing pump proportional to the water flow.
pulses to the dosing pump in proportion to the water flow. With the pulses and the programmed
The electronic system uses the pulses and the programmed "PERCENT" value to calculate the stroke frequency for dosing in proportion to the water flow.
For this, the pulse rate of the contact water meter (in imp./ltr. or ltr./imp.), as well as the
stroke volume (depending on the local system pressure) must also be set.BATCH - The pump doses a programmed quantity. The quantity can be set in millilitres (ml) or as a number of dosing strokes.
can be set. The pump can be started either manually via the front keys, by an external pulse generator via
the universal input "INPUT", or via a programmable time interval (countdown).mA - The stroke frequency of the pump - and thus the dosing capacity - is controlled by an external current signal (0-20 mA).
signal. The signal transmitter is connected to the universal input "INPUT".Volt - The stroke frequency of the pump - and thus the dosing capacity - is controlled by an external voltage signal (0-10
volts). The signal transmitter is connected to the universal input "INPUT".
Solenoid-operated dosing pumps with horizontal mounting, cost-effective and particularly reliable. K pumps are designed for universal use and various industries.The K series includes an MF version with multifunction software and an LPV version for viscous liquids. Also available with self-venting.Features at a glanceWith universal input for contact pulse or 0/4+20 mAStroke frequency proportional to input signal (0+180 imp/min) Universal input programmable as: - Pulse divider 1/10, 10/100, 100/1000- pulse multiplier 1*10 and then by means of rotary knob, infinitely adjustable Stroke length adjustment by means of rotary knob, stepless from 0...100% "LEVEL" connection for empty level switch "ALARM" relay output for empty signal (option)Operating mode: Constant Proportional via pulse divider Inputs:Level control (with pre-alarm)Digital signalVoltage signalOutput:Level alarm outputHydraulic parts:- PVDF- PP- stainless steel (AISI 316)- Acrylic glass (PMMA)- Check valves with double ball- O-rings made of FKM B, EPDM, nitrile, PTFEDiaphragm:PTFE diaphragmAccessories (selectable via the configurator)Suction lances:emec Viton suction lance with 40cm immersion length (with BNC connection)emec Viton suction lance with 122cm immersion length (with BNC connection)emec EPDM suction lance with 40cm immersion length (with BNC connection)emec EPDM suction lance with 122cm immersion length (with BNC connection)Included in delivery:Injection valve 1/2" - 4x6mm made of PVDF or PP, depending on the selected versionAxial foot valve with empty level switch and 2.5m connection cable with BNC plug2m pressure hose made of PVDF (for PVDF head) or PE (for PP head), 4x6mm or 6x8mm* (depending on version, see technical data) 2m suction hose PVC transparent, 4x6mm, 6x8mm*, 8x10mm (depending on version, see technical data) 2m vent hose PVC transparent, 4x6mm2.5m control cable RG174 with BNC plugOperating instructions6 plugs with screwsFine-wire fuse 4x20mmMode/LED - each functionCONSTANT - continuous operation with 1÷180 metering strokes per minuteCONSTANT/DIV 1:10 - continuous operation with 1÷18 metering strokes per minuteDIV 1:10 - Pulses coming from the "INPUT" connector are divided by the factor N = 1÷10 (adjustable with DK 2, grey scale)DIV 10:100 - Pulses coming from the "INPUT" connection are divided by a factor of 10÷100. With DK 2 (grey scale N = 1÷10) the factor can be set proportionally: N1 = /10 to N10 = /100DIV 100:1000 - Pulses coming from the "INPUT" connector are divided by a factor of 100÷1000. With DK 2 (grey scale N = 1÷10) the factor can be set proportionally: N1 = /100 to N10 = /1000MULT 1:10 - Pulses coming through the "INPUT" connector are multiplied by the factor N = 1÷10 (adjustable with DK 2, grey scale).mA - An analogue signal (0/4÷20 mA) coming from the "INPUT" connection generates dosing strokes according to the factor N = 1÷10 (adjustable with DK 2, grey scale).
Slow mode:With the exclusive SLOW MODE function of PRISMA dosing pumps, the stroke speed can be reduced from 100% to 1% during the priming cycle. This function facilitates the adaptation of the pump to the dosing medium and increases the reliability and deaeration of high viscosity dosing media.Colour display and encoder control:The PRISMA dosing pump is equipped with an encoder for quick and easy menu navigation, as well as a large display for a convenient setting of the operating parameters and monitoring of the pump functions.The intelligent multi-function software allows the operator to precisely set the dosage required by the application. This allows you to enter the desired value and read it directly in ml/h or l/h via the graphic display. All operating modes are displayed clearly and easily through self-explaining symbols.Operating mode:- Constant- Proportional control by external input, operating mode mg/l (ppm)- Proportional control by external input, operating mode percent (%)- Start-pause- Weekly timer- External input (start and/or pause)Turndown function:Prisma's stepper motor driven pumps offer the most precise control over stroke speed and provide an excellent turndown ratio of up to 4800:1. means that Prisma can divide the dosing process into a maximum of 4800 steps to ensure the most homogeneous and precise distribution of the product depending on the desired application to be dosed. Furthermore, the CC per pulse function provides additional dosing accuracy.Inputs:- Multifunction input- Level (with pre-alarm)- Pulse transmitter Water meter (PPM mode, %, mlq, mA, V, pulse)- Standby- External contact (voltage-free)Output:Alarm (common for all alarms)Interface:- RS485 / Modbus RTU (optional)- Bluetooth for remote control (optional on request)Hydraulic parts:- PVDF- PP- Stainless steel (AISI 316)- Acrylic glass (PMMA)- Check valves with double ball- O-rings made of FKM B, EPDM, nitrile, PTFEMembrane:PTFE diaphragmScope of delivery:1x PRISMA dosing pump 90 -240 VAC, 50/60 Hz with mains cable1x Axial foot valve with level switch / empty indicator made of PVDF or PP, depending on the selected version1x Injection valve 1/2" or 3/4" made of PVDF or PP, depending on the selected version1x 2m pressure hose made of PVDF (for PVDF head) or PE (for PP head), 4x6mm or 6x8mm* (depending on version, see technical data)1x 2m suction hose PVC transparent, 4x6mm, 6x8mm*, 8x10mm (depending on version, see technical data)1x 2m vent hose PVC transparent, 4x6mm1x 2m 3-pole signal cable for "ALARM" output1x 1.5m 5-pole signal cable for universal signal input "INPUT", standby input and external start1x instruction manual4x dowels (6mm diameter) 4x screws, 4.5 x 40 1x fine-wire fuse 5 x 20mm, ...AT* For 6x8mm only one hose (PE Matt) with 4m length, for two hoses, simply cut through.The operating modes at a glanceConstant - The pump delivers a constant quantity.ml per pulse -Dosage of a constant quantity per pulsePPM - proportional dosing in ppmPercent - proportional dosing in percentMLQ - dosing proportional to quantity in MLQBatch - use the pump to fill a containerVolt - control pump proportionally with 0-10V signalmA - control pump proportionally with 0/4-20mA signalPulse - control pump proportionally with pulse signal.Pause-run - set surge dosing time-controlled
The
dosing pumps with motor in the PRIUS series were developed by EMEC to meet the
highest requirements. The PRIUS D 50 Hz models ensure constant dosing and are
equipped with a PTFE diaphragm. They also offer a choice of different power
supply options including 380 VAC (three-phase), 220 VAC (single-phase) and 115
VAC (single-phase). In
addition, the dosing pumps are available in two different pump head types: PVDF
(polyvinylidene fluoride) and PP (polypropylene).
Outputs:
1000
l/h 100
bar
Power
supply:
380
VAC 220
VAC 115
VAC
Vent
pipe:
Manual Automatic
Features
Horizontal
mounting Aluminium
housing Spring
return mechanism Double
ball valves (if available) Mechanical
stroke adjustment Infinitely
variable flow control from 0 to 100% with MANUAL adjustment on the rotary knob Hydraulic
parts available in various sizes and materials Tropicalised
motor
Installation:
Installation kit A includedInstallation kit B and C sold
separatelyThe pump with AISI316L pump body does
not include installation accessories
The
dosing pumps with motor in the PRIUS series were developed by EMEC to meet the
highest requirements. The PRIUS D 50 Hz models ensure constant dosing and are
equipped with a PTFE diaphragm. They also offer a choice of different power
supply options including 380 VAC (three-phase), 240 VAC (single-phase) and 115
VAC (single-phase).
In
addition, the dosing pumps are available in two different pump head types: PVDF
(polyvinylidene fluoride) and PP (polypropylene).
Outputs:
950 l/h 100
bar
Power
supply:
380
VAC 220
VAC 115
VAC
Vent
pipe:
Manual Automatic
Features
Horizontal
mounting Aluminium
housing Spring
return mechanism Double
ball valves (if available) Mechanical
stroke adjustment Infinitely
variable flow control from 0 to 100% with MANUAL adjustment on the rotary knob Hydraulic
parts available in various sizes and materials Tropicalised
motor
Installation:
Installation kit A includedInstallation kit B and C sold
separatelyThe pump with AISI316L pump body does
not include installation accessories
The PRIUS motorised dosing pumps have a diaphragm and spring return. They combine efficiency and chemical resistance with a wide range of flow rates.They also offer a choice of different power supply options including 220 VAC (single-phase) and 115 VAC (single-phase). In addition, the dosing pumps are available in two different pump head types: PVDF (polyvinylidene fluoride) and PP (polypropylene).
Features
Multifunction pump
with single-phase power supply Operating mode:
constant, ppm, %, mlq, pause-work, weekly, pulse, mA, volt and batch Fill level control
Alarms Standby Double position of
the electronic unit (standard or rotated position) PTFE diaphragm Aluminium housing Spring return Manual venting of
the pump body (PVDF and PP) Mechanical stroke
adjustment Hydraulic parts
available in various sizes and materials Valves with double
ball Tropicalised
motors MODBUS option
The PRIUS piston dosing pumps have a spring return and combine efficiency and chemical resistance with a wide range of flow rates. They also offer a choice of different power supply options including 380 VAC (three-phase), 220 VAC (single-phase) and 115 VAC (single-phase). The pump head is made of PP (polypropylene).
features
Pump
with three-phase motor Ceramic
or stainless steel piston Aluminium
housing Mechanical
stroke adjustment Valves
with double ball Tropicalised
three-phase motors
Piston metering pump with spring return stroke. PRIUS P combines efficiency and chemical resistance with a wide range of flow rates.They also offer a choice of different power supply options including 380 VAC (three-phase), 220 VAC (single-phase) and 115 VAC (single-phase). The pump head is made of PP (polypropylene).Features
Pump with three-phase motor
Aluminum housing
Mechanical stroke adjustment
Valves with double ball
Tropical three-phase motors
Insulation class F
Energy efficiency IE 1
The PRIUS piston metering pumps feature a spring return and combine efficiency and chemical resistance with a wide range of flow rates. They also offer a choice of power supply options including 240 VAC (single-phase) and 115 VAC (single-phase). The pump head is made of PP (polypropylene).Features Multifunction pump with single-phase power supply Operating mode: constant, ppm, %, mlq, pause-work, pulse, weekly, mA, volt and batch Level control Alarms
Standby Double position of the electronic unit (standard or rotated position) Aluminium housing Mechanical stroke adjustment Hydraulic parts available in different sizes and materials Valves with double ball Tropicalised motors Insulation class F Energy efficiency IE 1