UMO Dtrans T100 screw-in RTD temperature probe with programmable transmitter, M12 x 1 machine plug connection Type: 902815/20-370-1013-2-6-100-380-24/452 Measuring range from -50 to + 150 °C 1x Pt1000 in four-wire circuit Tolerance class: Class A Thermowell diameter: 6 mm Installation length: 100 mm Process connection: G1/2 threaded connection with CIP-compliant sealing cone Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: Parts in contact with the medium electronically polished, roughness depth Ra 0,8 mm(withour thread and weld seams)  M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC). 

UMO Dtrans T100 screw-in RTD temperature probe with programmable transmitter, M12 x 1 machine plug connection Type: 902815/20-370-1013-2-6-100-104-24/000 Measuring range from -50 to + 150 °C 1x Pt1000 in four-wire circuit Tolerance class: Class A Thermowell diameter: 6 mm Installation length: 100 mm Process connection: G1/2 threaded connection Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: without M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC). 

UMO Dtrans T100 screw-in RTD temperature probe with programmable transmitter, M12 x 1 machine plug connection Type: 902815/20-370-1013-2-6-150-000-24/000 Measuring range from -50 to + 150 °C 1x Pt1000 in four-wire circuit Tolerance class: Class A Thermowell diameter: 6 mm Installation length: 150 mm Process connection: without Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: without M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC). 

UMO Dtrans T100 screw-in RTD temperature probe with programmable transmitter, M12 x 1 machine plug connection Type: 902815/20-370-1013-2-6-200-104-24/000 Measuring range from -50 to + 150 °C 1x Pt1000 in four-wire circuit Tolerance class: Class A Thermowell diameter: 6 mm Installation length: 200 mm Process connection: Screw connection G1/2 Thermowell material: Stainless steel 316 L (material no. 1.4404/1.4435) EU and China RoHS compliant Extra code: without M12 x 1 push-on connector; protection class IP67 to DIN EN 60529 with attached machine plug USB interface for configuration with setup programme The screw-in resistance thermometer in a compact design consists of a thermowell with built-in temperature sensor, a process connection and a housing for the transmitter electronics. The programmable two-wire transmitter offers a robust solution for the precise recording of temperatures in a temperature measuring range of -50 to + 150°C, with a neck tube up to 260°C and is therefore versatile in use. The device has a USB interface that enables simple configuration via a setup programme. With the help of this programme, parameters such as measuring range, fine adjustment and measuring circuit monitoring can be adjusted to meet the requirements of different applications. The output signal 4 to 20 mA or reversed 20 to 4 mA is available linearised (temperature linear). The device is intended for industrial use and complies with European standards to ensure electromagnetic compatibility (EMC). 

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-1003-1-6-50-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 50 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-1003-1-6-100-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 100 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-1003-1-6-150-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 150 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-1003-1-6-250-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 250 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-2003-1-6-50-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  2x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 50 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-2003-1-6-100-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 100 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-2003-1-6-150-104/000  With continuous protection tube  Measuring range from -50 to +400 °C  Single resistance thermometer  2x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 150 mm  Process connection: screw connection G ½  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

Screw-in resistance thermometer with form J connection head Type: 902030/10-402-1003-1-6-50-103/000  With continuous protection tube  Measuring range from -50 to 400 °C  Single resistance thermometer  1x Pt 100 in two-wire circuit  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Installation length: 50 mm  Process connection: screw connection G 3/8  Extra codes: none The screw-in RTD temperature probe with connection head is specially designed for use in various industries such as air conditioning and refrigeration technology and heating, furnace and apparatus engineering. It offers precise temperature measurement in both liquid and gaseous media, with a temperature range of -50 to +400 °C. The installation design of this thermometer ensures reliable tightness, even under extreme conditions of negative and positive pressure.The measuring insert is fitted as standard with a Pt100 temperature sensor in accordance with the DIN EN 60751:2009 / IEC 60751:2008 standards. This sensor has a temperature coefficient α of 3.850 × 10-3 °C-1 and is installed in a two-wire circuit. Versions with Pt500 or Pt1000 are also available as an option. For more precise measurement results, the connection can be made either in a three-wire or four-wire circuit, and it is also possible to integrate a transmitter into the connection head. Depending on the measurement requirements, a single or dual resistance thermometer can also be selected.

If you are looking for a pH electrode for demanding, contaminated, or highly alkaline media and value a robust design, clog-resistant diaphragm, and extended service life, this JUMO tecLine version is a strong choice. JUMO tecLine glass shaft pH electrode with salt reservoir, 120 mm immersion length, PTFE ring diaphragm and HA glass for high-alkali applications This JUMO tecLine pH electrode is designed for demanding pH measurements in process and industrial applications. It is particularly suitable for measuring points where standard electrodes quickly reach their limits, such as oily wastewater, suspensions, paints, or media containing solid particles. With HA glass for high-alkali applications, this version is also well suited for high pH environments. Advantages and special features The PTFE ring diaphragm is dirt-repellent and designed for minimal clogging. This is a clear advantage in media containing contamination or solids, as it makes the electrode more durable and suitable for everyday industrial use. Combined with the cartridge reference system and silver-ion-free reference electrolyte, it provides a robust solution for demanding process conditions. Why choose this electrode? This is a robust electrode for more challenging industrial media. The HA glass makes it suitable for high pH values, while the PTFE ring diaphragm offers advantages in applications where fouling or deposits can become an issue. The additional salt reservoir is especially beneficial when the electrode is used in low-conductivity media, as it can extend service life. This makes it ideal for users seeking a durable and long-life-oriented solution. With the Pg13.5 screw head (S8) and 120 mm immersion length, the electrode can be integrated into many common measuring points. The temperature range of -5 to +80 °C covers many typical process and water analysis applications. This version is therefore designed for industrial conditions requiring a robust pH electrode tailored to the medium. Typical applications industrial wastewater treatment process monitoring electroplating industry paper industry beverage industry oily wastewater, suspensions, paints media containing solid particles It is also suitable for fluoride-containing media up to 1000 mg/l HF. In the presence of electrode poisons, a double-chamber version is recommended, but this does not apply to this specific salt reservoir variant. Technical data Basic type: glass shaft Active element: HA glass Measuring range: pH 0 to 14 Temperature range: -5 to +80 °C Application: high-alkali use Diaphragm: PTFE ring Electrical connection: Pg13.5 screw head (S8) Immersion length: 120 mm (standard) Type extension: salt reservoir

Anyone looking for a tecLine pH electrode for industrial applications and placing particular value on quality, service life, and a process-suitable design will find a suitable solution here for demanding measurement tasks. JUMO tecLine pH glass shaft electrode with salt reservoir, 120 mm insertion length, 1x zirconium dioxide and UW glass The JUMO tecLine pH glass shaft electrode is designed for demanding pH measurements in process and industrial applications. It is intended for users who are not simply looking for any pH electrode, but for a high-quality version for reliable continuous operation in aqueous media. Especially in applications where measuring points must operate permanently stable and where downtime causes additional effort, a robust industrial electrode is essential. Advantages and special features A key advantage of this version lies in its industrially optimized design. The combination of UW glass, zirconium dioxide, and a salt reservoir makes the electrode particularly suitable for applications requiring long-lasting and stable pH measurement. The salt reservoir is especially beneficial in applications where the electrode is operated under conditions that require maximum service life. This makes the version attractive for users aiming to reduce maintenance effort and minimize replacement intervals. Why choose this electrode? This electrode is not designed for occasional spot measurements but for continuous use in process environments. It is built to operate reliably and deliver stable measurement values over extended periods. When pH measurement is an integral part of a plant or system, it makes sense to rely on a robust design. A high-quality electrode typically lasts longer and reduces the need for frequent replacements or troubleshooting due to failures. Technical information Basic type: glass shaft Active element: UW glass Measuring range: pH 0 to 12, short-term up to pH 14 Temperature range: -5 to +80 °C Diaphragm: 1 x zirconium dioxide Electrical connection: S8 Pg13.5 screw head Insertion length: 120 mm (standard) Type option: with salt reservoir The UW glass supports reliable pH measurement, while the overall design is optimized for stable measuring conditions in industrial environments. With a 120 mm insertion length, this electrode is suitable for many common installation situations in process and industrial systems. The tecLine series represents high-quality industrial electrodes designed for demanding measurement tasks. Depending on the configuration, variants with integrated temperature sensors are also available within the series, offering additional flexibility in selection. Applications This pH electrode is used wherever pH values in water and aqueous media must be reliably monitored. Process measurements in industrial plants Water treatment General industrial water analysis Process water and production processes with pH monitoring

This version is suitable according to the specifications provided. It is particularly well suited wherever a robust, clog-resistant, and service-life-oriented pH electrode is required for demanding media. JUMO tecLine glass shaft pH electrode with salt reservoir, 120 mm immersion length, annular gap diaphragm and UW glass This JUMO tecLine pH electrode is designed for demanding pH measurements in process and industrial applications. It is particularly suitable for measuring points where the electrode must not only provide reliable measurement but also cope with more challenging media. The combination of UW glass, annular gap diaphragm, and salt reservoir makes this version especially interesting for applications where conventional standard electrodes quickly reach their limits. Technical data Basic type: glass shaft Active element: UW glass Measuring range: pH 0 to 12, short-term up to pH 14 Temperature range: -5 to +80 °C Diaphragm: annular gap diaphragm, gel of polymerized solid electrolyte (“diaphragm-less”) Reference system: cartridge reference system Electrical connection: Pg13.5 screw head (S8) Immersion length: 120 mm (standard) Type extension: with salt reservoir Special features and advantages A key advantage of this version lies in the annular gap diaphragm with gel based on a polymerized solid electrolyte. This design is intended for applications where contamination, oil, or solid particles may be present. Compared to conventional diaphragm designs, it is optimized for clog-resistant operation, making it particularly suitable for more difficult media. This makes the electrode highly practical for industrial processes where clean laboratory conditions are not always available. Why choose this electrode? This version is particularly suitable when a pH electrode is required for contaminated, polluted, or solids-containing media and a longer service life is important. The salt reservoir is especially beneficial in low-conductivity media, as it can help extend electrode lifetime. This makes it more than a standard pH electrode—it is a solution designed for more demanding operating conditions in industrial environments. The UW glass is designed for pH measurements from pH 0 to 12, and short-term up to pH 14, and can be used in a temperature range from -5 to +80 °C. Combined with the cartridge reference system, it provides reliable measurement performance in general aqueous media as well as more demanding process environments. The Pg13.5 (S8) screw head ensures compatibility with many common measuring setups, while the 120 mm immersion length represents a standard and widely applicable configuration. Typical applications industrial wastewater treatment process monitoring electroplating industry paper industry beverage industry oily wastewater, suspensions, paints media containing solid particles fluoride-containing media up to 1000 mg/l HF If you are looking for a pH electrode designed for difficult process media and offering additional operational benefits through an annular gap diaphragm and salt reservoir, this JUMO tecLine version is an excellent choice. Additional information Annular gap diaphragm with polymerized solid electrolyte: This design is optimized for challenging media and helps reduce clogging during operation. This makes the electrode especially suitable for applications with dirt, oil, or solid particles.

This version is particularly suitable for users who are looking for a technically appropriate solution for high-alkalinity applications and want to rely on a robust industrial pH electrode. JUMO tecLine pH glass shaft electrode with salt reservoir, 120 mm immersion length, 1x zirconium dioxide and HA glass for high-alkali applications This JUMO tecLine pH electrode is designed for demanding pH measurements in process and industrial applications where standard versions may not be sufficient. Thanks to its HA glass for high-alkali applications, it is particularly suitable for measuring points where media with higher alkaline loads must be reliably monitored. Users looking for an electrode for more challenging operating conditions will find here an industrial-grade solution for stable and long-term measurement tasks. The key advantage of this version lies in the targeted combination of HA glass, zirconium dioxide diaphragm, and salt reservoir. The HA glass is designed for a measuring range from pH 0 to 14 and is specifically intended for applications where high pH values must also be measured reliably. This makes the version especially suitable for users working in alkaline environments who require a dedicated electrode design. The zirconium dioxide diaphragm supports stable reference behavior and ensures reliable measurement conditions during operation. Why choose this electrode? This version is not just a general-purpose pH electrode, but specifically designed for high-alkali applications. It is therefore particularly useful when measuring points operate in the upper pH range or when process media require an electrode optimized for alkaline conditions. The additional salt reservoir is another advantage when extended service life is required. This makes the electrode especially suitable for users who value a durable, robust, and process-ready solution. With its Pg13.5 screw head (S8) and 120 mm immersion length, the electrode can be integrated into many standard industrial measuring setups. The glass shaft represents a proven and widely used design in pH measurement technology. The operating temperature range of -5 to +80 °C further expands its usability in common water and process analytics applications. Typical applications This electrode is used wherever pH values in aqueous media must be measured reliably and where alkaline process conditions play an important role. Process and industrial applications Water treatment General water analysis Measurement points requiring electrodes for higher pH ranges Anyone requiring a pH electrode for demanding industrial measurements in alkaline environments will find this JUMO tecLine version a strong choice. It combines a purpose-oriented glass design with a robust technical foundation for reliable process measurements. Technical data Base type: glass shaft Active element: HA glass – special glass design for high pH values Measuring range: pH 0 to 14 Temperature range: -5 to +80 °C Application: high-alkali use – suitable for strongly alkaline media Diaphragm: 1 x zirconium dioxide – robust ceramic diaphragm for stable measuring conditions Electrical connection: Pg13.5 screw head (S8) Immersion length: 120 mm (standard) Additional feature: salt reservoir

If you are looking for a pH electrode for demanding industrial media and value a robust standard design, a clog-resistant PTFE ring diaphragm, and reliable pH measurement, this JUMO tecLine version is a strong choice. JUMO tecLine glass shaft pH electrode without type extension, 120 mm immersion length, PTFE ring diaphragm and UW glass This JUMO tecLine pH electrode is designed for demanding pH measurements in process and industrial applications. It is particularly suitable for measuring points where a robust and reliable standard design without additional type extensions is required. The combination of UW glass and PTFE ring diaphragm makes this version especially suitable for applications involving more challenging media, where a conventional standard electrode may quickly reach its limits. Technical data Basic type: glass shaft Active element: UW glass Measuring range: pH 0 to 12, short-term up to pH 14 Temperature range: -5 to +80 °C Diaphragm: PTFE ring Electrical connection: Pg13.5 screw head (S8) Immersion length: 120 mm (standard) Type extensions: none Typical applications industrial wastewater treatment process monitoring electroplating industry paper industry beverage industry oily wastewater suspensions and paints media containing solid particles fluoride-containing media up to 1000 mg/l HF Advantages and special features A key advantage of this electrode is the dirt-repellent PTFE ring diaphragm. It is designed for minimal clogging, making it particularly suitable for media where deposits, dirt, or solid particles can occur. This makes the design especially attractive for users who need a pH electrode that performs reliably under demanding industrial conditions. Why choose this electrode? This version is particularly suitable when a robust pH electrode is required for challenging media, but no additional special features are needed. It focuses on the essentials: a durable basic design, stable measuring conditions, and a technically sound standard solution for a wide range of industrial applications. This is especially beneficial when a long-lasting and proven solution is required without relying on type extensions. The UW glass is designed for pH measurements from pH 0 to 12, and short-term up to pH 14, and can be used in a temperature range from -5 to +80 °C. It is complemented by the proven cartridge reference system with silver-ion-free reference electrolyte, ensuring stable measurement conditions during operation. With the Pg13.5 screw head (S8) and 120 mm immersion length, the electrode can be integrated into many common measuring points.

Thanks to the compact Pg13.5 screw head and 120 mm immersion length, this version is particularly practical for applications where a classic design with a standardized length is required. JUMO tecLine pH glass shaft electrode without type extension, 120 mm immersion length, zirconium dioxide diaphragm and C-glass (subline) This JUMO tecLine pH electrode is designed for reliable pH measurements in process and industrial applications and is particularly suitable for users who are looking for a high-quality standard version without additional type extensions. It is an excellent choice for measuring points where a classic glass shaft electrode with clearly defined technical characteristics is required, intentionally omitting special features. Advantages and special features A key advantage of this version lies in its simple yet industrial-grade design. The C-glass serves as the active measuring element for pH detection, making the electrode suitable for general applications in water and aqueous media. The zirconium dioxide diaphragm ensures stable measuring conditions and represents a robust ceramic design well-suited for regular use in industrial environments. Technical data Basic type: glass shaft Active element: C-glass Diaphragm: zirconium dioxide Electrical connection to electrode: Pg13.5 screw head Immersion length: 120 mm Why choose this electrode? This version is particularly suitable when a reliable standard pH electrode is required for classic process or industrial applications. As it is supplied without type extensions, it focuses on the essentials and is ideal for users who prefer a technically clean basic design. This simplifies selection and is especially beneficial wherever no additional special features are required. With the Pg13.5 screw head, the electrode can be integrated into many common installation situations. The 120 mm immersion length corresponds to a typical standard design and therefore fits many standard measuring points. Typical applications This pH electrode is used wherever the pH value in water and general aqueous media needs to be reliably monitored. Process and industrial applications Water treatment general water analysis measuring points requiring a robust and uncomplicated glass shaft electrode without additional special features If you are looking for a high-quality standard version for pH measurement and prefer a clear, durable and industrial-grade solution, this JUMO tecLine version is an excellent choice.

This pH electrode is used wherever the pH value in water and general aqueous media must be reliably monitored. Thanks to its robust design, it can be used in a wide range of industrial installations. JUMO tecLine pH glass shaft electrode without additional options, 225 mm immersion length, zirconium dioxide diaphragm and UW glass This pH electrode is designed for reliable pH measurements in process and industrial applications and is particularly suitable for measuring points where a high-quality standard version without additional special features is required. With its 225 mm immersion length, it is especially suitable when a longer electrode is needed and a 120 mm version is not sufficient. Features and advantages A major advantage of this version is its clear and technically straightforward basic configuration. The UW glass is designed for pH measurements in general aqueous media and makes this electrode a suitable solution for many standard industrial and process applications. The zirconium dioxide diaphragm supports stable measurement conditions and is a robust ceramic design suitable for reliable operation in continuous use. Why choose this electrode? This version is especially suitable for users who specifically require a classic glass shaft electrode without additional options. It focuses on the essentials: a high-quality basic design, an extended immersion length, and stable pH measurement without additional special features. This is a clear advantage in many applications, as it simplifies selection and allows easy integration into existing standard measuring points. With its Pg13.5 screw head, the electrode is compatible with many common installation and connection setups. The 225 mm immersion length makes it particularly suitable for measuring points with greater insertion depth or applications requiring a longer design. Technical data Base type: glass shaft Active element: UW glass Diaphragm: zirconium dioxide Electrical connection: Pg13.5 screw head Immersion length: 225 mm Typical applications Process and industrial applications Water treatment General water analysis Measuring points requiring a longer glass shaft electrode without additional options Users looking for a high-quality extended standard pH electrode and a robust, industrial-grade tecLine solution will find this version a strong choice.

The JUMO tecLine pH electrode is a high-quality standard version for reliable pH measurements in water and general aqueous media. JUMO tecLine pH glass shaft electrode without additional options, 120 mm insertion length, 1x zirconium dioxide and UW glass The JUMO tecLine pH electrode is designed for reliable pH measurements in process and industrial applications. It is particularly suitable for users looking for a high-quality industrial electrode for water and general aqueous media, while valuing a solid, durable, and clearly defined standard version. Why choose this electrode? This version is ideal when a pH electrode without additional special options is required, focusing on the essentials: stable measurement values a robust basic design reliable integration into common industrial measuring points In process applications, this is often an advantage, as a clearly defined standard version simplifies selection and is fully sufficient for many routine measurement tasks. Typical applications Process measurements in industrial plants general water analysis water treatment As well as other applications where pH values in aqueous media must be reliably monitored. This electrode is especially suitable when a high-quality industrial electrode is required for regular use without the need for additional special features. Technical data Basic type: glass shaft Active element: UW glass Measuring range: pH 0 to 12, short-term up to pH 14 Temperature range: -5 to +80 °C Diaphragm: 1 x zirconium dioxide Electrical connection: S8 Pg13.5 screw head Insertion length: 120 mm (standard) Additional options: none The UW glass is designed for pH measurements in the range of pH 0 to 12, with short-term operation up to pH 14, and can be used in a temperature range of -5 to +80 °C. This makes the electrode suitable for many typical applications in water and process analytics. The zirconium dioxide diaphragm complements the design with a stable and process-suitable reference junction for general industrial measurement tasks. With the S8 Pg13.5 screw head and a 120 mm insertion length, the electrode can be integrated into many common installation situations. As this version is supplied without additional options, it is particularly suitable for users who deliberately choose a classic and straightforward standard design.

These amperometric sensors with membrane are used to determine the concentration of free chlorine. They are able to measure various inorganic chlorine compounds, including chlorine gas (Cl₂), electrolytically generated chlorine, sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂) and chlorinated lime (Ca(OCl)Cl). Testing for the complete absence of free chlorine is not possible with these sensors. Depending on the version, the sensors either supply a temperature-compensated current signal (4-20 mA) in an analogue version or a Modbus RTU signal via a digital interface. Calibration takes place in a downstream device such as an indicator, controller, recorder or programmable logic controller (PLC). The sensors can be connected directly to various transmitters or controllers. These supply the system with the required voltage and enable uncomplicated calibration. Areas of application: The sensors are used to measure free chlorine in drinking water, bathing water, industrial water, process water and cooling water.

These amperometric sensors with membrane are used to determine the concentration of free chlorine. They are able to measure various inorganic chlorine compounds, including chlorine gas (Cl₂), electrolytically generated chlorine, sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂) and chlorinated lime (Ca(OCl)Cl). Testing for the complete absence of free chlorine is not possible with these sensors. Depending on the version, the sensors either supply a temperature-compensated current signal (4-20 mA) in an analogue version or a Modbus RTU signal via a digital interface. Calibration takes place in a downstream device such as an indicator, controller, recorder or programmable logic controller (PLC). The sensors can be connected directly to various transmitters or controllers. These supply the system with the required voltage and enable uncomplicated calibration. Areas of application: The sensors are used to measure free chlorine in drinking water, bathing water, industrial water, process water and cooling water.

These amperometric sensors with membrane are used to determine the concentration of free chlorine. They are able to measure various inorganic chlorine compounds, including chlorine gas (Cl₂), electrolytically generated chlorine, sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂) and chlorinated lime (Ca(OCl)Cl). Testing for the complete absence of free chlorine is not possible with these sensors. Depending on the version, the sensors either supply a temperature-compensated current signal (4-20 mA) in an analogue version or a Modbus RTU signal via a digital interface. Calibration takes place in a downstream device such as an indicator, controller, recorder or programmable logic controller (PLC). The sensors can be connected directly to various transmitters or controllers. These supply the system with the required voltage and enable uncomplicated calibration. Areas of application: The sensors are used to measure free chlorine in drinking water, bathing water, industrial water, process water and cooling water.

These amperometric sensors with membrane are used to determine the concentration of free chlorine. They are able to measure various inorganic chlorine compounds, including chlorine gas (Cl₂), electrolytically generated chlorine, sodium hypochlorite (NaOCl), calcium hypochlorite (Ca(OCl)₂) and chlorinated lime (Ca(OCl)Cl). Testing for the complete absence of free chlorine is not possible with these sensors. Depending on the version, the sensors either supply a temperature-compensated current signal (4-20 mA) in an analogue version or a Modbus RTU signal via a digital interface. Calibration takes place in a downstream device such as an indicator, controller, recorder or programmable logic controller (PLC). The sensors can be connected directly to various transmitters or controllers. These supply the system with the required voltage and enable uncomplicated calibration. Areas of application: The sensors are used to measure free chlorine in drinking water, bathing water, industrial water, process water and cooling water.