JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/11-0-15-009/994 Basic type extension: RH-T Version: Standard Measuring range: 0 ... 100 % rH / -40 ... +80°C Output: 4 ... 20 mA / 0 ... 10 V combi output config. Extra code: with integrated display Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/11-0-15-530/000 Basic type extension: RH-T Version: Standard Measuring range: 0 ... 100 % rH / -40 ... +80°C Output: RS-485 Modbus Extra code: without Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/12-0-17-535/994 Basic type extension: RH-T-CO2 Version: Standard Measuring range: 0 ... 95 % rH / -10 ... +60°C / 10.000 ppm Output: SPE with PoDL (modbus TCP slave) Extra code: Integrated display Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/11-0-15-530/994 Basic type extension: RH-T Version: Standard Measuring range: 0 ... 100 % rH / -40 ... +80°C Output: RS-485 Modbus Extra code: Integrated display Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/12-0-17-009/000 Basic type extension: RH-T-CO2 Version: Standard Measuring range: 0 ... 95 % rH / -10 ... +60°C / 10.000 ppm Output: 4 bis 20 mA / 0 bis 10 V combi output configurable Extra code: without Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/12-0-17-009/994 Basic type extension: RH-T-CO2 Version: Standard Measuring range: 0 ... 95 % rH / -10 ... +60°C / 10.000 ppm Output: 4 ... 20 mA / 0 ... 10 V combi output config. Extra code: Integrated display Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/12-0-17-530/000 Basic type extension: RH-T-CO2 Version: Standard Measuring range: 0 ... 95 % rH / -10 ... +60°C / 10.000 ppm Output: RS-485 Modbus Extra code: without Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S20 - Humidity and temperature transmitter with optional wall-mounted CO2 module Typ: 907042/12-0-17-530/994 Basic type extension: RH-T-CO2 Version: Standard Measuring range: 0 ... 95 % rH / -10 ... +60°C / 10.000 ppm Output: RS-485 Modbus Extra code: Integrated display Measuring parameters: Temperature, relative humidity, carbon dioxide (CO2) optional Interfaces: USB, RS485, Sigle Pair Ethernet (SPE) Robustness Easy to install Multi-sensor Optional plastic sintered filter The humidity and temperature transducer monitors the quality of the ambient air and can be wall-mounted both indoors and in protected outdoor areas. Areas of application Climate monitoring Ventilation systems Building management Storage rooms 

JUMO hydro TRANS S30 - Humidity and temperature transmitter with optional CO2 module in duct version Typ: 907043/11 Basic type extension: RH-T Version: StandardMeasuring range: 0 to 100 % RH/-40 to +80 °COutput: 4 to 20 mA/0 to 10 V combined output configuredExtra code: Without Measuring parametersTemperatureRelative humidityCarbon dioxide (CO2) optional InterfacesUSB PORTRS485 Areas of applicationClimate monitoringVentilation systemsBuilding managementStorage roomsRailroad applications according to DIN EN 50155 Special featuresRobustnessEasy to installMultisensorOptional plastic sintered filter The humidity and temperature transducer monitors the outside air flowing into buildings and production processes. It is suitable for installation in weather-protected ventilation ducts.

JUMO hydro TRANS S30 - Humidity and temperature transmitter with optional CO2 module in duct versionTyp: 907043/11 Basic type extension: RH-T Version: StandardMeasuring range: 0 to 100 % RH/-40 to +80 °COutput: RS485 ModbusExtra code: Without Measuring parametersTemperatureRelative humidityInterfacesRS485 Areas of applicationClimate monitoringVentilation systemsBuilding managementStorage roomsRailroad applications according to DIN EN 50155 Special featuresRobustnessEasy to installMultisensorOptional plastic sintered filter The humidity and temperature transducer monitors the outside air flowing into buildings and production processes. It is suitable for installation in weather-protected ventilation ducts.

JUMO hydro TRANS S30 - Humidity and temperature transmitter with optional CO2 module in duct version Typ: 907043/12 Basic type extension: RH-T Version: StandardMeasuring range: 0 to 95 % RH/-10 to +60 °COutput: 4 to 20 mA/0 to 10 V combined output configuredExtra code: Without Measuring parametersTemperatureRelative humidityCarbon dioxide (CO2) optional InterfacesUSB PORTRS485 Areas of applicationClimate monitoringVentilation systemsBuilding managementStorage roomsRailroad applications according to DIN EN 50155 Special featuresRobustnessEasy to installMultisensorOptional plastic sintered filter The humidity and temperature transducer monitors the outside air flowing into buildings and production processes. It is suitable for installation in weather-protected ventilation ducts.

JUMO hydro TRANS S30 - Humidity and temperature transmitter with optional CO2 module in duct versionTyp: 907043/12 Basic type extension: RH-T-CO2Version: StandardMeasuring range: 0 to 95 % RH/-10 to +60 °COutput: RS-485 ModbusExtra code: Without Measuring parametersTemperatureRelative humidityCarbon dioxide (CO2) optional InterfacesUSB PORTRS485 Areas of applicationClimate monitoringVentilation systemsBuilding managementStorage roomsRailroad applications according to DIN EN 50155 Special featuresRobustnessEasy to installMultisensorOptional plastic sintered filter The humidity and temperature transducer monitors the outside air flowing into buildings and production processes. It is suitable for installation in weather-protected ventilation ducts.

Push-in resistance thermometer in water vapour-tight designType: 902830/10-370-1011-2-6-100-11-2500/317 Measuring range -50 to +150°C Connection cable: PTFE 1x Pt 100 in four-wire circuit  Single resistance thermometer Tolerance class A according to DIN EN 60 751 Thermowell diameter: 6 mm Insertion length: 100 mm Connection cable end: Wire end ferrules to DIN 46 228 Connection cable length: 2500 mm (standard) Extra codes: Shielded connecting cableThe plug-in resistance thermometer in water vapour-tight design is preferably used for temperature measurements in sterilisers. Their specific design allows them to be used in atmospheres containing water vapour and under pressure. Another area of application is in apparatus engineering and laboratory technology. The thermometer can be supplied with a PTFE connection cable, which enables operation in humid rooms in the temperature range from -50 to +150 °C, or alternatively an FEP connection cable is available, which covers temperatures from -70 to +200 °C.The transition of the connection cable is strain-relieved to ensure the longevity of the connection. The measuring insert is equipped as standard with a Pt 100 temperature insert in accordance with DIN EN 60 751, class A in a two-wire circuit. In addition, the connection can optionally be made in three- and four-wire circuits to meet individual requirements.

Push-in resistance thermometer in water vapour-tight designType: 902830/10-370-2001-2-6-100-11-2500/000  Measuring range -50 to +150°C Connection cable: PTFE 2x Pt 100 in Three-wire circuit  Single resistance thermometer Tolerance class A according to DIN EN 60 751 Thermowell diameter: 6 mm Insertion length: 100 mm Connection cable end: Wire end ferrules to DIN 46 228 Connection cable length: 2500 mm (standard) Extra codes: Shielded connecting cableThe plug-in resistance thermometer in water vapour-tight design is preferably used for temperature measurements in sterilisers. Their specific design allows them to be used in atmospheres containing water vapour and under pressure. Another area of application is in apparatus engineering and laboratory technology. The thermometer can be supplied with a PTFE connection cable, which enables operation in humid rooms in the temperature range from -50 to +150 °C, or alternatively an FEP connection cable is available, which covers temperatures from -70 to +200 °C.The transition of the connection cable is strain-relieved to ensure the longevity of the connection. The measuring insert is equipped as standard with a Pt 100 temperature insert in accordance with DIN EN 60 751, class A in a two-wire circuit. In addition, the connection can optionally be made in three- and four-wire circuits to meet individual requirements.

Push-in resistance thermometer in water vapour-tight design, pressure-tight up to 5.0 barType: 902830/30-302-1011-2-4-50-11-2500/000  Measuring range -70 to +200°C Connection cable: FEP 1 x Pt 100 in four-wire circuit  Single resistance thermometer Tolerance class A according to DIN EN 60 751 Thermowell diameter: 4 mm Insertion length: 50 mm Connection cable end: Wire end ferrules to DIN 46 228 Connection cable length: 2500 mm (standard) Extra codes: without extra codeThe insertion resistance thermometer in water vapour-tight design is preferably used for temperature measurements in sterilisers. Their specific design allows them to be used in atmospheres containing water vapour and under pressure. Another area of application is in apparatus engineering and laboratory technology. The thermometer can be supplied with a PTFE connection cable, which enables operation in humid rooms in the temperature range from -50 to +150 °C, or alternatively an FEP connection cable is available, which covers temperatures from -70 to +200 °C.The transition of the connection cable is strain-relieved to ensure the longevity of the connection. The measuring insert is equipped as standard with a Pt 100 temperature insert in accordance with DIN EN 60 751, class A in a two-wire circuit. In addition, the connection can optionally be made in three- and four-wire circuits to meet individual requirements.

Push-in resistance thermometer in water vapour-tight design, pressure-tight up to 5.0 barType: 902830/30-302-2011-2-4,5-50-11-2500/000  Measuring range -70 to +200°C Connection cable: FEP 2 x Pt 100 in four-wire circuit  Single resistance thermometer Tolerance class A according to DIN EN 60 751 Thermowell diameter: 4.5mm with 2 measuring circuits in four-wire circuit Installation length: 50 mm Connection cable end: Wire end ferrules according to DIN 46 228 Connection cable length: 2500 mm (standard) Extra codes: without extra codeThe plug-in resistance thermometer in water vapour-tight design is preferably used for temperature measurements in sterilisers. The specific design makes it suitable for use in atmospheres containing water vapour and under pressure. Another area of application is in apparatus engineering and laboratory technology. The thermometer can be supplied with a PTFE connection cable, which enables operation in humid rooms in the temperature range from -50 to +150 °C, or alternatively an FEP connection cable is available, which covers temperatures from -70 to +200 °C.The transition of the connection cable is strain-relieved to ensure the longevity of the connection. The measuring insert is equipped as standard with a Pt 100 temperature insert in accordance with DIN EN 60 751, class A in a two-wire circuit. In addition, the connection can optionally be made in three- and four-wire circuits to meet individual requirements.

Type: 902150/40-397-1003-1-6-60-11-2500/317  Temperature measuring range: -50 ... +350 °C / Metal mesh  Measuring insert: 1x Pt 100 in two-wire circuit  Installation length: 60 mm  Cable length: 2500 mm  Tolerance class: Class B (standard)  Thermowell diameter: 6 mm  Wire end ferrules  Extra code: Shielded connecting cable  Available as single and dual resistance thermometers  Available in straight and angled versions to meet different installation requirements.  Flexible connection cables  Strain relief to protect against mechanical stress  Meets SIL and PL qualification standards for maximum safety  Optional kink protection Areas of application:  Laboratory technology  Climate cabinets  Solar systems  Heating, air conditioning, ventilation  Apparatus engineering The insertion resistance thermometer offers precise temperature measurement in both liquid and gaseous media. The wide range of variants makes it ideal for various applications in industrial environments.This thermometer ensures reliable performance in dry and damp rooms and enables accurate temperature measurements. The robust design and flexible configuration options ensure precise temperature monitoring.

Push-in resistance thermometer with spiralised connection cable, one-piece stainless steel protection tube Type: 902150/30-388-1003-1-6-100-11-2500/315,317 Temperature measuring range: -50 ... +260 °C / metal braiding Measuring insert: 1x Pt 100 in two-wire circuit Installation length: 100 mm Cable length: 2500 mm Tolerance class: Class B (standard) Thermowell diameter: 6 mm Wire end ferrules Extra code: with bend protection, cable shielded Available as single and double resistance thermometers Available in straight and angled versions to meet different installation requirements. Flexible connection cables Strain relief to protect against mechanical stress Meets SIL and PL qualification standards for maximum safety Optional kink protection Areas of application: Areas of application: Laboratory technology Climate cabinets Solar systems Heating, air conditioning, ventilation Apparatus engineering The insertion resistance thermometer offers precise temperature measurement in both liquid and gaseous media. The wide range of variants makes it ideal for various applications in industrial environments. This thermometer ensures reliable performance in dry and damp rooms and enables accurate temperature measurements. The robust design and flexible configuration options ensure precise temperature monitoring. 

Push-in resistance thermometer with spiralised connection cable, one-piece stainless steel protection tube Type: 902150/30-388-1001-1-6-100-11-2500/315,317 Temperature measuring range: -50 ... +260 °C / metal mesh Measuring insert: 1x Pt 100 in three-wire circuit Installation length: 100 mm Cable length: 2500 mm Tolerance class: Class B (standard) Thermowell diameter: 6 mm Wire end ferrules Extra code: with bend protection, cable shielded Available as single and double resistance thermometers Available in straight and angled versions to meet different installation requirements. Flexible connection cables Strain relief to protect against mechanical stress Meets SIL and PL qualification standards for maximum safety Optional kink protection Areas of application: Areas of application: Laboratory technology Climate cabinets Solar systems Heating, air conditioning, ventilation Apparatus engineering The insertion resistance thermometer offers precise temperature measurement in both liquid and gaseous media. The wide range of variants makes it ideal for various applications in industrial environments. This thermometer ensures reliable performance in dry and damp rooms and enables accurate temperature measurements. The robust design and flexible configuration options ensure precise temperature monitoring. 

Push-in resistance thermometer with spiralised connection cable, one-piece stainless steel protection tube Type: 902150/30-402-1001-1-6-150-11-2500/315,317 Temperature measuring range: -50 ... +400 °C / Metal mesh Measuring insert: 1x Pt 100 in three-wire circuit Installation length: 150 mm Cable length: 2500 mm Tolerance class: Class B (standard) Thermowell diameter: 6 mm Wire end ferrules Extra code: with bend protection, cable shielded Available as single and double resistance thermometers Available in straight and angled versions to meet different installation requirements. Flexible connection cables Strain relief to protect against mechanical stress Meets SIL and PL qualification standards for maximum safety Optional kink protection Areas of application: Areas of application: Laboratory technology Climate cabinets Solar systems Heating, air conditioning, ventilation Apparatus engineering The insertion resistance thermometer offers precise temperature measurement in both liquid and gaseous media. The wide range of variants makes it ideal for various applications in industrial environments. This thermometer ensures reliable performance in dry and damp rooms and enables accurate temperature measurements. The robust design and flexible configuration options ensure precise temperature monitoring. 

Push-in resistance thermometer with spiralised connection cable, one-piece stainless steel protection tube Type: 902150/20-730-1003-1-6-50-11-1100/000 Temperature measuring range: -5 ... +105 °C Measuring insert: 1x Pt 100 in two-wire circuit Installation length: 50 mm Cable length: 1100 mm (stretched) Tolerance class: Class B (standard) Thermowell diameter: 6 mm Wire end ferrules Extra code: without Available as single and dual resistance thermometers Available in straight and angled versions to meet different mounting requirements. Flexible connection cables Strain relief to protect against mechanical stress Meets SIL and PL qualification standards for maximum safety Optional kink protection Areas of application: Laboratory technology Climate cabinets Solar systems Heating, air conditioning, ventilation Apparatus engineering The insertion resistance thermometer offers precise temperature measurement in both liquid and gaseous media. The wide range of variants makes it ideal for various applications in industrial environments. This thermometer ensures reliable performance in dry and damp rooms and enables accurate temperature measurements. The robust design and flexible configuration options ensure precise temperature monitoring. 

JUMO meroVIEW - Multifunction digital indicator with PLC function Typ: 701553/8-00-00-00-00-00-00-23/000  Version: Standard with factory settings  Power supply: AC 10 to 240 V +10/-15% / 48 to 63 Hz  Extra code: without  Option1-6: not assigned  1 analogue input  1 digital input  1 digital input/output switchable  1 relay (NO contact)  2 timers  Min/max display  Hold function  Tare function The display series comprises four universally applicable devices in various DIN formats, which are used to display temperature, pressure and other process variables.The devices offer user-friendly operation with a clearly structured layout and text support. Process values and parameters are displayed on two 18-segment LCD displays. Types 701552, 701553 and 701554 also have a pixel matrix LCD display for displaying texts. Additional display elements provide information about the switching positions of the outputs and certain functions such as timers. The devices are operated via a membrane keypad with 4 buttons and can also be used in demanding environments thanks to their high IP65 protection rating.The basic equipment already includes a min/max value display, hold function, temperature function, limit value monitoring, digital control signals, extensive timer functions and a service counter. Optionally, the devices can be extended with a maths and logic function as well as with ST code functionality to realise customer-specific functions. The ST code functionality also allows direct access to the display and operating buttons, which enables customised device operation. Inputs and outputsEach device type is equipped with a universal analogue input that is suitable for resistance thermometers, thermocouples, current, voltage, resistance transmitters and resistance/potentiometers. Each device also has a digital input, a switchable digital input/output and two relay outputs (NO contact 3 A). The digital inputs are intended for the connection of a potential-free contact, while the digital output supplies a logic signal of 0/14 V.The optional digital outputs with 0/14 V (not galvanically isolated) can be used, for example, to control solid-state relays. Alternatively, the optional digital outputs with 0/22 V and galvanic isolation can also be used as a voltage supply for two-wire transmitters.Please note that certain inputs and outputs cannot be used simultaneously (see notes in the wiring diagram). Customer-specific linearisationIndividual linearisation according to customer requirements also makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup program either using your value table with up to 40 value pairs or using a formula (4th order polynomial). The device supports 2 customer-specific linearisations. Counting inputsThe device can optionally be equipped with up to 4 counting inputs, with a maximum counting frequency of 12.5 kHz. Each counting input can be controlled either with a digital signal of 0/24 V or via a potential-free contact. The counters allow the following functions to be configured:  Counting of pulses  Calculation of frequency  speed  Speed (volume per time unit)  Flow rate (volume per time unit) In addition, individual functions can be implemented via maths functions or ST code, such as the calculation of the total flow rate (volume) Signal assignment via selectorsThe input signals and all internal signals are available in so-called selectors (analogue selector, digital selector) for further use in the device. The control signals for the outputs are also assigned via selectors, which enables flexible assignment of signals and functions. USB interfacesThe device has a USB device interface (Micro-B socket on the rear), which is intended exclusively for connection to a PC for use with the setup programme. There is also a USB host interface (type A socket), which is located on the rear of the 108 and 104 format devices and on the side of the smaller 116 format device. This interface is intended for connecting a USB memory stick in order to carry out firmware updates, read out data loggers and transfer the device configuration. RS485 interfaceThe RS485 interface is available as an option and supports the Modbus RTU protocol. It can be used in both master and slave mode. Ethernet interfaceThe Ethernet interface (Modbus TCP) is optional and enables parallel communication with 2x mater or 2x slave. It is used for integration into a company network, the transfer of process values and communication with the setup programme. PROFINET interfaceThe device can optionally be equipped with a PROFINET interface in order to be integrated into a PROFINET network as an IO device. A GSD file (GSDML) is available for the programming system of the IO controller, which describes the properties of the device. It should be noted that the standard Ethernet services are not supported via the PROFINET interface. If the device is equipped with the PROFINET interface, neither the Ethernet nor the RS485 interface can be used. Power supplyThe device is available in two power supply variants: AC 110 to 240 V or AC/DC 24 V (see Technical data). Electrical connectionThe electrical connection is time-saving with removable spring-loaded terminals (PushIn technology). Min-max functionWhen the min-max function is activated, both the minimum and maximum values of the indicator are saved and continuously updated. These values can be displayed separately or alternating with the current value. In the alternating display (scrolling), the min/max symbol is active while either the minimum or maximum value is displayed. A binary signal can be used to reset the stored values in order to return to the current value. Hold functionThe hold function "freezes" the value of the indicator, which means that this value is displayed as long as the controlling binary signal is active. Tare functionThe tare function makes it possible to set the value of the indicator to zero, controlled by a binary signal (for weighing applications). The currently displayed value is added to the tare value each time. Another binary signal can be used to reset the tare value to zero so that the current value appears on the display again. Limit value monitoringThe device is equipped with 8 limit value monitors, each of which has 8 configurable alarm functions. Any analogue signal is selected from a selector for monitoring, while the limit value can either be an absolute value or dependent on another analogue signal. It offers special functions such as  On/off delay  Wiper function  Alarm suppression during the switch-on phase or in the event of parameter changes Alarm latching  Latching with acknowledgement Limit value monitoring enables a variety of alarm and limit value functions. Digital control signalsThis function enables the configuration of up to 8 digital control signals. The control signal is either formed by an AND/OR/XOR combination of up to three selectable binary signals or a single binary signal is used as an input signal and can be output as a pulsed signal, delayed signal, wiper signal or edge-triggered signal. In the latter case, the rising or falling edge of the binary signal is determined and the output signal is activated for the duration of a sampling interval. The output signal can be inverted in all these cases. TimerThe device is also equipped with 2 timers that can be started via freely selectable digital signals or depending on an integrated tolerance band monitoring function. Lead and lag times as well as a self-hold function with acknowledgement are also available. This makes it easy to realise a wide range of functions such as time-controlled regulation or setpoint switching. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Maths and logic functionThe optional maths and logic function (extra code) can be used to link analogue or binary values. Up to four freely configurable maths or logic formulas can be created using the setup program. The results are then available for further use in the analogue or digital selector. Structured textThe "Structured text" option (extra code) allows the user to develop a customised application. This application is created using the ST editor, which is part of the setup programme, and uses the "Structured text" PLC programming language. Once completed, the application is transferred to the device and executed continuously. Online debugger functions are available in the ST editor for troubleshooting and testing.With the setup programme, the user can also create up to 100 individual texts and have them shown on the device display by a corresponding application. These texts can be entered in four languages so that they are displayed in the respective language after changing the device language. Data loggerThe data logger enables the recording of 4 analogue and 4 binary values. The recording interval is adjustable and ranges from 1 minute to 1 hour. Recording is based on the ring memory principle, which means that older data is overwritten as soon as the memory is full. With a recording interval of 10 minutes, the data can be recorded for around 2 years before the oldest data is overwritten. A USB memory stick on which the data is stored in CSV format is used to read out the data. Real-time clockThe real-time clock provides the current date and time (time stamp for data logger and ST code). Retain memoryThanks to the integrated retain memory, specific data is retained even in the event of a power failure. This applies to the service data, the counter and timer data as well as the retain data of the ST code. Individually configurable operating levelsThe user has the option of customising the device menu to ensure a high level of operating convenience and optimum integration into the system. Four menu levels with submenus are available for this purpose. The menu items and parameters can be labelled individually in four languages, and it is possible to switch between them. The menu levels can be partially or completely locked to prevent unauthorised operation. Setup programmeThe setup programme is essential for commissioning the device and is available to download free of charge. In addition to the individual set-up of the operating levels, whose parameters can subsequently be edited in the device, the setup programme offers the user a simple and user-friendly method of configuring the device using a PC. With the setup programme, data records can be created, edited, transferred to the device and read out from there. The data can be saved and printed out. The programme also allows the user to easily create and print out a connection diagram showing the current terminal assignment of the device. Startup: The startup function enables the recording of process variables during commissioning for a maximum of 24 hours. The recorded diagrams are available on the PC and can be used for system documentation, for example. Online data: The current process variables of the device are displayed in a separate window. Firmware update The device's firmware can be updated in a user-friendly way using a USB memory stick; the file is provided by the manufacturer if required.

JUMO meroVIEW - Multifunction digital indicator with PLC function Typ: 701553/8-00-00-00-00-00-00-42/000  Version: Standard with factory settings  Power supply: AC/DC 24V +10/-15% / 48 bis 63 Hz  Extra code: without  Option1-6: not assigned  1 analogue input  1 digital input  1 digital input/output switchable  1 relay (NO contact)  2 timers  Min/max display  Hold function  Tare function The display series comprises four universally applicable devices in various DIN formats, which are used to display temperature, pressure and other process variables.The devices offer user-friendly operation with a clearly structured layout and text support. Process values and parameters are displayed on two 18-segment LCD displays. Types 701552, 701553 and 701554 also have a pixel matrix LCD display for displaying texts. Additional display elements provide information about the switching positions of the outputs and certain functions such as timers. The devices are operated via a membrane keypad with 4 buttons and can also be used in demanding environments thanks to their high IP65 protection rating.The basic equipment already includes a min/max value display, hold function, temperature function, limit value monitoring, digital control signals, extensive timer functions and a service counter. Optionally, the devices can be extended with a maths and logic function as well as with ST code functionality to realise customer-specific functions. The ST code functionality also allows direct access to the display and operating buttons, which enables customised device operation. Inputs and outputsEach device type is equipped with a universal analogue input that is suitable for resistance thermometers, thermocouples, current, voltage, resistance transmitters and resistance/potentiometers. Each device also has a digital input, a switchable digital input/output and two relay outputs (NO contact 3 A). The digital inputs are intended for the connection of a potential-free contact, while the digital output supplies a logic signal of 0/14 V.The optional digital outputs with 0/14 V (not galvanically isolated) can be used, for example, to control solid-state relays. Alternatively, the optional digital outputs with 0/22 V and galvanic isolation can also be used as a voltage supply for two-wire transmitters.Please note that certain inputs and outputs cannot be used simultaneously (see notes in the wiring diagram). Customer-specific linearisationIndividual linearisation according to customer requirements also makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup program either using your value table with up to 40 value pairs or using a formula (4th order polynomial). The device supports 2 customer-specific linearisations. Counting inputsThe device can optionally be equipped with up to 4 counting inputs, with a maximum counting frequency of 12.5 kHz. Each counting input can be controlled either with a digital signal of 0/24 V or via a potential-free contact. The counters allow the following functions to be configured:  Counting of pulses  Calculation of frequency  speed  Speed (volume per time unit)  Flow rate (volume per time unit) In addition, individual functions can be implemented via maths functions or ST code, such as the calculation of the total flow rate (volume) Signal assignment via selectorsThe input signals and all internal signals are available in so-called selectors (analogue selector, digital selector) for further use in the device. The control signals for the outputs are also assigned via selectors, which enables flexible assignment of signals and functions. USB interfacesThe device has a USB device interface (Micro-B socket on the rear), which is intended exclusively for connection to a PC for use with the setup programme. There is also a USB host interface (type A socket), which is located on the rear of the 108 and 104 format devices and on the side of the smaller 116 format device. This interface is intended for connecting a USB memory stick in order to carry out firmware updates, read out data loggers and transfer the device configuration. RS485 interfaceThe RS485 interface is available as an option and supports the Modbus RTU protocol. It can be used in both master and slave mode. Ethernet interfaceThe Ethernet interface (Modbus TCP) is optional and enables parallel communication with 2x mater or 2x slave. It is used for integration into a company network, the transfer of process values and communication with the setup programme. PROFINET interfaceThe device can optionally be equipped with a PROFINET interface in order to be integrated into a PROFINET network as an IO device. A GSD file (GSDML) is available for the programming system of the IO controller, which describes the properties of the device. It should be noted that the standard Ethernet services are not supported via the PROFINET interface. If the device is equipped with the PROFINET interface, neither the Ethernet nor the RS485 interface can be used. Power supplyThe device is available in two power supply variants: AC 110 to 240 V or AC/DC 24 V (see Technical data). Electrical connectionThe electrical connection is time-saving with removable spring-loaded terminals (PushIn technology). Min-max functionWhen the min-max function is activated, both the minimum and maximum values of the indicator are saved and continuously updated. These values can be displayed separately or alternating with the current value. In the alternating display (scrolling), the min/max symbol is active while either the minimum or maximum value is displayed. A binary signal can be used to reset the stored values in order to return to the current value. Hold functionThe hold function "freezes" the value of the indicator, which means that this value is displayed as long as the controlling binary signal is active. Tare functionThe tare function makes it possible to set the value of the indicator to zero, controlled by a binary signal (for weighing applications). The currently displayed value is added to the tare value each time. Another binary signal can be used to reset the tare value to zero so that the current value appears on the display again. Limit value monitoringThe device is equipped with 8 limit value monitors, each of which has 8 configurable alarm functions. Any analogue signal is selected from a selector for monitoring, while the limit value can either be an absolute value or dependent on another analogue signal. It offers special functions such as  On/off delay  Wiper function  Alarm suppression during the switch-on phase or in the event of parameter changes Alarm latching  Latching with acknowledgement Limit value monitoring enables a variety of alarm and limit value functions. Digital control signalsThis function enables the configuration of up to 8 digital control signals. The control signal is either formed by an AND/OR/XOR combination of up to three selectable binary signals or a single binary signal is used as an input signal and can be output as a pulsed signal, delayed signal, wiper signal or edge-triggered signal. In the latter case, the rising or falling edge of the binary signal is determined and the output signal is activated for the duration of a sampling interval. The output signal can be inverted in all these cases. TimerThe device is also equipped with 2 timers that can be started via freely selectable digital signals or depending on an integrated tolerance band monitoring function. Lead and lag times as well as a self-hold function with acknowledgement are also available. This makes it easy to realise a wide range of functions such as time-controlled regulation or setpoint switching. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Maths and logic functionThe optional maths and logic function (extra code) can be used to link analogue or binary values. Up to four freely configurable maths or logic formulas can be created using the setup program. The results are then available for further use in the analogue or digital selector. Structured textThe "Structured text" option (extra code) allows the user to develop a customised application. This application is created using the ST editor, which is part of the setup programme, and uses the "Structured text" PLC programming language. Once completed, the application is transferred to the device and executed continuously. Online debugger functions are available in the ST editor for troubleshooting and testing.With the setup programme, the user can also create up to 100 individual texts and have them shown on the device display by a corresponding application. These texts can be entered in four languages so that they are displayed in the respective language after changing the device language. Data loggerThe data logger enables the recording of 4 analogue and 4 binary values. The recording interval is adjustable and ranges from 1 minute to 1 hour. Recording is based on the ring memory principle, which means that older data is overwritten as soon as the memory is full. With a recording interval of 10 minutes, the data can be recorded for around 2 years before the oldest data is overwritten. A USB memory stick on which the data is stored in CSV format is used to read out the data. Real-time clockThe real-time clock provides the current date and time (time stamp for data logger and ST code). Retain memoryThanks to the integrated retain memory, specific data is retained even in the event of a power failure. This applies to the service data, the counter and timer data as well as the retain data of the ST code. Individually configurable operating levelsThe user has the option of customising the device menu to ensure a high level of operating convenience and optimum integration into the system. Four menu levels with submenus are available for this purpose. The menu items and parameters can be labelled individually in four languages, and it is possible to switch between them. The menu levels can be partially or completely locked to prevent unauthorised operation. Setup programmeThe setup programme is essential for commissioning the device and is available to download free of charge. In addition to the individual set-up of the operating levels, whose parameters can subsequently be edited in the device, the setup programme offers the user a simple and user-friendly method of configuring the device using a PC. With the setup programme, data records can be created, edited, transferred to the device and read out from there. The data can be saved and printed out. The programme also allows the user to easily create and print out a connection diagram showing the current terminal assignment of the device. Startup: The startup function enables the recording of process variables during commissioning for a maximum of 24 hours. The recorded diagrams are available on the PC and can be used for system documentation, for example. Online data: The current process variables of the device are displayed in a separate window. Firmware update The device's firmware can be updated in a user-friendly way using a USB memory stick; the file is provided by the manufacturer if required.

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-459-405-502-20-601-23/000  Input: 0 to 10 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Quickon  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter.  JUMO MIDAS – Intelligent Transmitters for Precise Analytical Data The JUMO MIDAS is a versatile transmitter and controller specifically designed for the precise evaluation of analytical sensors. It supports various measurement parameters such as pH, redox, conductivity, oxygen, and temperature, and offers flexible interfaces for integration into automation and process control systems. In the HeylNeomeris range, the MIDAS impresses with its compact design, intuitive operation, and extensive configuration options – ideal for demanding measurement and control tasks in water treatment, environmental analysis, and industry. Why we use the JUMO MIDAS: • Versatile use for numerous measurement parameters • Accurate and stable measurement results even during continuous operation • Modern communication interfaces for easy integration • User-friendly menu and flexible alarm management • Robust and reliable in industrial applications Example of a JUMO MIDAS model in the HeylNeomeris range: • JUMO MIDAS C08 – Transmitter for pH, redox, conductivity, and oxygen with multiple measurement channels (Item no.: 802091)