JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-456-405-502-20-601-61/000  Input: 0 to 2,5 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-457-405-502-20-601-61/000  Input: 0 to 4 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-458-405-502-20-601-61/000  Input: 0 to 6 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-460-405-502-20-601-61/000  Input: 0 to 16 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-460-405-504-20-601-61/000  Input: 0 to 16 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/2 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-462-405-502-20-601-61/000  Input: 0 to 40 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-480-405-502-20-601-61/000  Input: -1 to 1,5 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-481-405-502-20-601-61/000  Input: -1 to 3 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-455-405-502-20-601-61/000  Input: 0 to 1,6 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO Midas C08 - OEM - Basic pressure transmitter Typ: 401002/000-459-405-502-20-601-61/000  Input: 0 to 10 bar relative pressure  Output: 4 to 20 mA, two-wire  Process connection: G 1/4 DIN EN 837  Process connection material: CrNi (stainless steel)  Seal material: CrNi (stainless steel)  Electrical connection: Cable socket DIN EN 175301-803, form A  Extra code: none  New quality level especially for the OEM sector  Long-term stability below 0.2%  Temperature compensation range extended by 50% to -20 to +100 °C  Device installation 60% faster thanks to QUICKON quick-clamp technology  Vibration resistance 2.5 times higher than the industry standard  Manufactured in Germany For applications that require reliable and long-term realisation of measurement tasks, the pressure transmitter from the Midas family is used as a basic product. In addition to the basic product, the Midas family offers solutions for every specific task. The innovative and patented sensor design of the specially developed ceramic sensor results in excellent long-term stability < 0.2%. The transmitter detects relative pressures from 1.6 to 60 bar in gaseous or liquid media. Areas of application:  Mechanical and plant engineering  compressors  Building services engineering  Industrial pneumatics  Commercial vehicles Added value for the customer:  Process reliability: Thanks to design measures, the pressure transmitter has excellent vibration resistance and can be used under high vibration loads, such as those that occur in commercial vehicles. A fully automatic measuring and calibration system, diagnostic function of the circuit and 100% final inspection guarantee the highest quality.  Cost-effectiveness: QUICKON quick-clamp technology enables time-saving and safe installation. The spring contacts ensure reliable contacting even in the event of temperature fluctuations. This electrical connection shortens assembly times and reduces costs by 60% compared to conventional connection variants.  Versatility: The large selection of measuring ranges as well as process and electrical connections enables universal use of the pressure transmitter. 

JUMO miro TRON - electronic thermostat with PID two-point controller option Typ: 701081/0-01-24-02/000  Input: 1 resistance thermometer Pt100, Pt1000 in two-wire circuit, 1 digital input  Output: 4 relays (NO contact AC 250 V, 2.5 A), resistive load, only for type 701081  Power supply: AC 230 V, +10/-15 %, 48 to 63 Hz  With max. 4 relays  Version: Standard version  Extra code: without The electronic thermostat is used as a heating or cooling thermostat, but can be optionally extended with a PID two-point controller option. The device offers user-friendly operation, characterised by a clear structure and supporting texts in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information on the switching positions of the outputs, the status of the timer and the temperature unit used. PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. PID two-point controller (optional)If the PID two-point controller option is selected, various controller structures are available, including P, I, PH, PI and PID, which also enable self-optimisation. In addition, the setup programme offers a start-up function and a display of the online parameters. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket, which is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made in a time-saving manner using spring-loaded terminals (push-in technology) Self-optimisation  Self-optimisation (oscillation method) makes it possible even for users with no knowledge of control technology to adapt the controller to the controlled system. The reactions of the controlled system to changes in the manipulated variable are analysed and certain controller parameters are calculated.  Limit value monitoring  The device has three limit value monitors, each of which offers eight configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:   On/off delay - Wiper function   Alarm suppression during the switch-on phase or when parameters are changed   Alarm latching   Latching with acknowledgement are available.  Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerAfter the timer is activated, a signal is output for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached. After the timer has elapsed, an end signal can be generated that is either limited in time or can be deactivated by acknowledgement. The timer makes it possible, for example, to realise a time-controlled setpoint changeover. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated that must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme allows the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro TRON - electronic thermostat with PID two-point controller option Typ: 701080/0-01-23-02/000  Input: 1 resistance thermometer Pt100, Pt1000 in two-wire circuit, 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (NO contact AC 250 V, 5 A), resistive load  Power supply: AC 230 V+10/-15%, 48 bis 63 Hz  Version: Standard version  Extra code: without The electronic thermostat is used as a heating or cooling thermostat, but can be optionally extended with a PID two-point controller option. The device offers user-friendly operation, characterised by a clear structure and supporting texts in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information on the switching positions of the outputs, the status of the timer and the temperature unit used. PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. PID two-point controller (optional)If the PID two-point controller option is selected, various controller structures are available, including P, I, PH, PI and PID, which also enable self-optimisation. In addition, the setup programme offers a start-up function and a display of the online parameters. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket, which is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made in a time-saving manner using spring-loaded terminals (push-in technology) Self-optimisationSelf-optimisation (oscillation method) makes it possible even for users with no knowledge of control technology to adapt the controller to the controlled system. The reactions of the controlled system to changes in the manipulated variable are analysed and certain controller parameters are calculated. Limit value monitoringThe device has three limit value monitors, each of which offers eight configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerOnce the timer has been activated, a signal is emitted for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached. After the timer has elapsed, an end signal can be generated that is either limited in time or can be deactivated by acknowledgement. The timer makes it possible, for example, to realise a time-controlled setpoint changeover. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated that must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme allows the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro TRON - electronic thermostat with PID two-point controller option Typ: 701080/0-01-23-30/000  Input: 1 resistance thermometer Pt100, Pt1000 in two-wire circuit, 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (NO contact AC 250 V, 5 A), resistive load  Power supply: DC 12 bis 24 V +15/-15%  Version: Standard version  Extra code: without The electronic thermostat is used as a heating or cooling thermostat, but can be optionally extended with a PID two-point controller option. The device offers user-friendly operation, characterised by a clear structure and supporting texts in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information on the switching positions of the outputs, the status of the timer and the temperature unit used. PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. PID two-point controller (optional)If the PID two-point controller option is selected, various controller structures are available, including P, I, PH, PI and PID, which also enable self-optimisation. In addition, the setup programme offers a start-up function and a display of the online parameters. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket, which is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made in a time-saving manner using spring-loaded terminals (push-in technology) Self-optimisationSelf-optimisation (oscillation method) makes it possible even for users with no knowledge of control technology to adapt the controller to the controlled system. The reactions of the controlled system to changes in the manipulated variable are analysed and certain controller parameters are calculated. Limit value monitoringThe device has three limit value monitors, each of which offers eight configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerOnce the timer has been activated, a signal is emitted for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached. After the timer has elapsed, an end signal can be generated that is either limited in time or can be deactivated by acknowledgement. The timer makes it possible, for example, to realise a time-controlled setpoint changeover. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated that must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme allows the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro TRON - electronic thermostat with PID two-point controller option Typ: 701080/0-04-23-02/000  Input: 1 thermocouple and 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (NO contact AC 250 V, 5 A), resistive load  Power supply: AC 230 V+10/-15%, 48 bis 63 Hz  Version: Standard version  Extra code: without The electronic thermostat is used as a heating or cooling thermostat, but can be optionally extended with a PID two-point controller option. The device offers user-friendly operation, characterised by a clear structure and supporting texts in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information on the switching positions of the outputs, the status of the timer and the temperature unit used. PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. PID two-point controller (optional)If the PID two-point controller option is selected, various controller structures are available, including P, I, PH, PI and PID, which also enable self-optimisation. In addition, the setup programme offers a start-up function and a display of the online parameters. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket, which is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made in a time-saving manner using spring-loaded terminals (push-in technology) Self-optimisationSelf-optimisation (oscillation method) makes it possible even for users with no knowledge of control technology to adapt the controller to the controlled system. The reactions of the controlled system to changes in the manipulated variable are analysed and certain controller parameters are calculated. Limit value monitoringThe device has three limit value monitors, each of which offers eight configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerOnce the timer has been activated, a signal is emitted for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached. After the timer has elapsed, an end signal can be generated that is either limited in time or can be deactivated by acknowledgement. The timer makes it possible, for example, to realise a time-controlled setpoint changeover. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated that must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme allows the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro TRON - electronic thermostat with PID two-point controller option Typ: 701080/0-05-23-02/000  Input: 0(4) to 20 mA and 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (NO contact AC 250 V, 5 A), resistive load  Power supply: AC 230 V+10/-15%, 48 bis 63 Hz  Version: Standard version  Extra code: without The electronic thermostat is used as a heating or cooling thermostat, but can be optionally extended with a PID two-point controller option. The device offers user-friendly operation, characterised by a clear structure and supporting texts in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information on the switching positions of the outputs, the status of the timer and the temperature unit used. PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. PID two-point controller (optional)If the PID two-point controller option is selected, various controller structures are available, including P, I, PH, PI and PID, which also enable self-optimisation. In addition, the setup programme offers a start-up function and a display of the online parameters. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket, which is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made in a time-saving manner using spring-loaded terminals (push-in technology) Self-optimisationSelf-optimisation (oscillation method) makes it possible even for users with no knowledge of control technology to adapt the controller to the controlled system. The reactions of the controlled system to changes in the manipulated variable are analysed and certain controller parameters are calculated. Limit value monitoringThe device has three limit value monitors, each of which offers eight configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerOnce the timer has been activated, a signal is emitted for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached. After the timer has elapsed, an end signal can be generated that is either limited in time or can be deactivated by acknowledgement. The timer makes it possible, for example, to realise a time-controlled setpoint changeover. Service counterThe service counter can either count the number of switching operations of a binary signal or measure its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated that must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme allows the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro VIEW - smart digital indicator with limit value monitoring Typ: 701580/0-01-23-02  Input: 1 resistance thermometer Pt100, Pt1000 in two-wire circuit, 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (make contact AC 250 V, 5 A) resistive load  Power supply: AC 230 V +10/-15 %, 48 to 63 Hz The smart digital indicator is used to electronically display various process variables. The device records the process variables via resistance thermometer, thermocouple, current 0(4) to 20 mA or voltage 0 to 10 V. Other functions include limit value monitoring, min/max value storage, hold function and tare function. The device can be supplied either with 2 relays or with 1 relay and 1 digital output (DC0/14 V). It is characterised by user-friendly, clear operation in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information about  Switching positions of the outputs  Status of the timer  Temperature unit PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. Display functionIn addition to the conventional display of the measured value, the device offers additional functions such as  Display of min/max values  Hold function to hold the current measured value  Tare function for weighing applications Some of these functions can be configured using the membrane keypad on the front. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket that is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made using time-saving spring-loaded terminals (push-in technology) Limit value monitoringThe device has three limit value monitors, each of which offers two configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerAfter the timer is activated, a signal is output for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached.The service counter is used either to count the switching frequency of a binary signal or to determine its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme enables the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro VIEW - smart digital indicator with limit value monitoring Typ: 701580/0-01-23-30  Input: 1 resistance thermometer Pt100, Pt1000 in two-wire circuit, 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (make contact AC 250 V, 5 A) resistive load  Power supply: DC 12 bis 24 V +15/-15% The smart digital indicator is used to electronically display various process variables. The device records the process variables via resistance thermometer, thermocouple, current 0(4) to 20 mA or voltage 0 to 10 V. Other functions include limit value monitoring, min/max value storage, hold function and tare function. The device can be supplied either with 2 relays or with 1 relay and 1 digital output (DC0/14 V). It is characterised by user-friendly, clear operation in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information about  Switching positions of the outputs  Status of the timer  Temperature unit PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. Display functionIn addition to the conventional display of the measured value, the device offers additional functions such as  Display of min/max values  Hold function to hold the current measured value  Tare function for weighing applications Some of these functions can be configured using the membrane keypad on the front. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket that is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made using time-saving spring-loaded terminals (push-in technology) Limit value monitoringThe device has three limit value monitors, each of which offers two configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerAfter the timer is activated, a signal is output for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached.The service counter is used either to count the switching frequency of a binary signal or to determine its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme enables the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro VIEW - smart digital indicator with limit value monitoring Typ: 701580/0-04-23-02  Input: 1 Thermoelement und 1 Digitaleingang  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (make contact AC 250 V, 5 A) resistive load  Power supply: AC 230 V +10/-15 %, 48 to 63 Hz The smart digital indicator is used to electronically display various process variables. The device records the process variables via resistance thermometer, thermocouple, current 0(4) to 20 mA or voltage 0 to 10 V. Other functions include limit value monitoring, min/max value storage, hold function and tare function. The device can be supplied either with 2 relays or with 1 relay and 1 digital output (DC0/14 V). It is characterised by user-friendly, clear operation in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information about  Switching positions of the outputs  Status of the timer  Temperature unit PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. Display functionIn addition to the conventional display of the measured value, the device offers additional functions such as  Display of min/max values  Hold function to hold the current measured value  Tare function for weighing applications Some of these functions can be configured using the membrane keypad on the front. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket that is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made using time-saving spring-loaded terminals (push-in technology) Limit value monitoringThe device has three limit value monitors, each of which offers two configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerAfter the timer is activated, a signal is output for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached.The service counter is used either to count the switching frequency of a binary signal or to determine its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme enables the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

JUMO miro VIEW - smart digital indicator with limit value monitoring Typ: 701580/0-05-23-02  Input: 0(4) to 20mA and 1 digital input  Output: 1 relay (changeover contact AC 250 V, 10 A) and 1 relay (make contact AC 250 V, 5 A) resistive load  Power supply: AC 230 V +10/-15 %, 48 to 63 Hz The smart digital indicator is used to electronically display various process variables. The device records the process variables via resistance thermometer, thermocouple, current 0(4) to 20 mA or voltage 0 to 10 V. Other functions include limit value monitoring, min/max value storage, hold function and tare function. The device can be supplied either with 2 relays or with 1 relay and 1 digital output (DC0/14 V). It is characterised by user-friendly, clear operation in German, English, French and Spanish. Process values, texts and parameters are displayed on two 18-segment LCD displays. Additional display elements provide information about  Switching positions of the outputs  Status of the timer  Temperature unit PCB terminals with push-in technology enable quick electrical installation. Operation, parameterisation and configuration are carried out via a membrane keypad with four buttons. Display functionIn addition to the conventional display of the measured value, the device offers additional functions such as  Display of min/max values  Hold function to hold the current measured value  Tare function for weighing applications Some of these functions can be configured using the membrane keypad on the front. Inputs and outputsThe required analogue input can be selected when ordering:  Resistance thermometer  Thermocouple  Current (4 to 20 mA)  Voltage (0 to 10 V) There is also a digital input for connecting a potential-free contact (not for resistance thermometers in three-wire circuit). Depending on the device type, the following combinations are available as outputs: 2 relays (1 changeover contact, 1 NO contact), or 1 relay (NO contact) and 1 digital output DC 0/14 V, or 4 relays (NO contact). USB device interfaceThe device has a Micro-B socket that is intended for connection to a PC for configuration with the setup programme. No separate power supply is required during configuration via the USB interface (USB-powered). Electrical connectionThe electrical connection is made using time-saving spring-loaded terminals (push-in technology) Limit value monitoringThe device has three limit value monitors, each of which offers two configurable alarm functions. Any analogue signal is selected from a selector as the value to be monitored. The limit values can be defined either as an absolute value or as a different analogue signal. Additional functions:  On/off delay  Wiper function  Alarm suppression during the switch-on phase or when parameters are changed  Alarm latching  Latching with acknowledgement are available. Comprehensive alarm and limit value functions can be realised with limit value monitoring. TimerAfter the timer is activated, a signal is output for the preset runtime, which can be inverted. The timer can also be started after a lead time has elapsed or a tolerance limit has been reached.The service counter is used either to count the switching frequency of a binary signal or to determine its switch-on duration. As soon as the adjustable limit value is reached, a binary signal is activated and must be acknowledged. An operating hours counter is also available, which records the operating time of the device. Setup programmeThe optional setup programme enables the user to configure the device easily and conveniently via a PC. With this programme, data can be created, edited, transferred to the device and read out from there. It also offers a recording function for commissioning (start-up). Customer-specific linearisationIndividual linearisation according to customer requirements makes it possible to use sensor signals with special characteristics. Programming is carried out in the setup programme either using your value table with up to 40 value pairs or using a formula (4th order polynomial)

Room, outdoor and duct resistance thermometers Typ: 902520/15-361-1003-1/000 Measuring range from -50 to +90°C  Measuring insert 1x temperature sensor Pt100 in two-wire circuit Transmitter: without Protection class IP65 Suitable for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.

Room, outdoor and duct resistance thermometers Typ: 902520/15-361-1005-1/000 Measuring range from -50 to +90°C Measuring insert 1x temperature sensor Pt1000 in two-wire circuit Transmitter: without Protection class IP65 Suitable for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.

Room, outdoor and duct resistance thermometers Typ: 902520/15-361-1003-1/903, Measuring range from -50 to +90°C  Measuring insert 1x temperature sensor Pt100 in two-wire circuit Transmitter: without Cable gland (IP65) Protection class IP65 Suitable for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.

Room, outdoor and duct resistance thermometers Typ: 902520/15-361-1005-1/903 Measuring range from -50 to +90°C  Measuring insert 1x temperature sensor Pt1000 in two-wire circuit Transmitter: without Cable gland (IP65) Protection class IP65 Suitable for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.

Room, outdoor and duct resistance thermometers Typ: 902520/11-635-1003-1/000 Measuring range from -20 to +80°C  Measuring insert 1x temperature sensor Pt100 in two-wire circuit Transmitter: without Protection class IP54 Suitable for use in air conditioning technology Room, outdoor and duct resistance thermometers are designed for air conditioning technology and are mainly used for temperature measurement in rooms, air ducts and outdoors. Various plastic device versions with different degrees of protection are available for the respective measuring task. A Pt100 temperature sensor in accordance with DIN EN 60751 class B in a two-wire circuit is installed as standard, but variants with Pt500, Pt1000, Ni1000 and various NTC sensors are also possible. The connection terminals allow optional continuation in three- and four-wire circuits. An integrated measuring transducer can also be selected as an option.